Difference between revisions of "Team:Bordeaux/Bacteria results"

E. coli Results

CHOICE OF MATERIALS

M63 and LB media

Curdlan production was carried out in two different media: LB medium and M63 medium.
✵ We worked on M63 medium because a mineral salt medium is used on the literature [1]. M63 is a minimal, low osmolarity medium for E.coli, resulting in slower growth rate of these cells.
→ With this medium of known composition we were able to control parameters for the production of our molecule of interest.
✵We worked also on LB medium because this is the most common medium used in the laboratory.

[1] Dae-Young J, Young-Su C. Improved production of Curdlan with concentrated cells of Agrobacterium sp. Biotechnol. Bioprocess Eng. 2001,6:107-111

LABORATORY WORK

4.Purification and Quantitative analysis

To obtain Curdlan, cells were chemically destroyed by NaOH and many centrifugations.
Curdlan purification was performed by neutralization after adding acetic acid.
Quantitative analysis was done before and after purification to compare and eliminate non significant measures (background signal).

N.B. Also, we use a polarimeter to characterize our Curdlan molecule produced.

E. coli RESULTS

We produced some Curdlan compared to non transformed strain of DH5α. We analyzed data with a student test to prove our results are significant. The theoretical concentration obtained in the Control condition corresponds to the non significant measure (background signal).
N.B. We realized these figures by doing the average of all production results in each medium.

Figure 5: Quantitative analysis of purified Curdlan with aniline blue

→ Each medium can be used for the Curdlan production. But, we can’t compare these two results and say that produced Curdlan quantity is higher in LB than in M63 medium because productions are not realized at the same time in these cases.

In following results, we have studied production in M63 and LB media started at the same time.

Figure 6: Quantitative analysis of purified Curdlan with aniline blue

→ Now, thanks to a statistic test, we can conclude that Curdlan production is doubled in LB medium compared to M63 medium.

LB medium has an unknown glucose concentration contained in yeast extract whereas in M63 medium we have controled this parameter. We suppose that LB glucose concentration is higher than in the second medium. That will be explain the difference between these two conditions.

However, compared to Saccharomyces cerevisiae, our results are very low: about 10 to 20µg/mL for Bacteria to 100µg/mL for Yeast.

We have tried some optimization protocols but without success.

Characterization

Part 1. To verify OsmY promoter is only active in the stationary phase, we realized Curdlan quantitative analysis every hour of a culture in LB medium. The switch of temperature for the culture is linked to the transition in stationary phase.
→ As we can see, Curdlan appears after the switch at 27°C. So, OsmY promoter is active in stationary phase only. (Fig.7)

Figure 7: OsmY promoter characterization

Part 2. To verify produced molecule is Curdlan, we analysed samples with a polarimeter. The reference used was Curdlan bought to do standard range for the quantitative analysis with aniline blue.

A substance is optically active or has a rotatory power when it deflects polarization plane of light from an α angle. This rotatory power is related to the presence of one or more asymmetric carbon within the molecule. All sugars (except dihydroxyacetone) are chiral molecules, so they all have a rotatory power. This property allows the polarimetric determination of sugars in pure solution thanks to the law of Biot.

There are two types of optically active substances:
✵Those which deflect polarization plane of light from an α angle to the right. The measured angle is positive and the substance is in dextrorotatory form.
✵Those which deflect polarization plane of light from an α angle to the left. The measured angle is negative and the substance is in levorotatory form.

Results
– Results were obtained with a Jasco P-2000 polarimeter.
– Measures are done at 25°C.

	Optical rotation monitor
Reference	-0.1902
produced Curdlan	-0.1982
Control	0.0590

At the end...

We have obtained 3.44g of Curdlan in one month of production and with one single gene!

Perspectives

Despite amplification problems of two genes, we performed cloning with the crdA and crdC sequences. Each gene was placed into plasmids possessing resistance to a different antiobiotic:
✵pUC-OsmY-crdS (Ampicillin resistance)
✵pSB1C3-OsmY-crdA (Chloramphenicol resistance)
✵pSB3T5-OsmY-crdC (Tetracycline resistance)
We have tried without success a triple transformation.

We hope that production yield of Curdlan would be higher if the three genes were present.

Successful results	Unsuccessful results	Perspectives
PCR amplification of crdS	No PCR amplification on crdA and crdC	Sulfation step
Cloning in pSB1C3 and pUC	No production with transformed bacteria containing the three genes	Test on other E.coli strain
Transformation in DH5a strain	Bad purification method	Optimized Curdlan production protocol
Curdlan production and characterization		Test of produced Curdlan on plants

After production of Curdlan , we tested his effect on grapevine at INRA (National Institute of Agronomic Research) . With the help of Mr Anthony Bellée, our teammate applicator Curdlan to young leafs (4/5 days),and the day after she infects the leafs with Downy Mildew (see protocol page). The tests results will be available on Monday September 23th after the wiki freeze so we will present them at our presentation in Boston.

1

2

3

4

5

6

7

8

9

10