Difference between revisions of "Team:UChile-OpenBio/Modelling"

Bioreactor
What is a bioreactor?
Is an equipment which keeps an active biological environment and is used to carry out a transformation due to the performance of a biocatalyst (1). In this project, these biocatalysts are bacteria.
Why is important a bioreactor?
“The heart of a typical bioprocess is the reactor or fermenter. Flanked by unit operations which carry out physical changes for medium preparation and recovery of products, the reactor is where the major chemical and biochemical transformations occur. In many bioprocesses, characteristics of the reaction determine to a large extent the economic feasibility of the project.”[2] How works a bioreactor? Para preguntar A bioreactor is an equipment in which some substrates, from the culture, are transformed to a product through the performance of bacteria. A bioreactor gives all necessary conditions for the culture, like mixing, temperature regulation, oxygen supply, substrates ports, sampling ports, pH control, etc. Then, within bioreactor is carrying out a bio-reaction, because this equipment gives operation conditions for a complete reaction. There are three ways to carry out the reaction after charging the bioreactor with cell y substrate: giving a continuous feed (substrate), giving a semi-continuous feed and without feed, they are called a continuous, fed-batch and batch bioreactor respectively [3].
In this project, a continuous bioreactor was used. Thus, a continuous feed rate is equal to an outflow rate, maintaining a constant volume within bioreactor. Once PLA is produced, it is got from the outflow and then will be purified to use it to make any PLA product.

Which are the goals of a bioreactor?
These are the goals of a bioreactor[1]
Keep cells distributed uniformly.
Keep temperature constant and homogeneous
Minimize nutrient concentration gradients
Preventing sedimentation and flocculation
Allow gas diffusion
Aseptic environment culture
Sampling ports
Foam control
Maximize performance and production
Reduce production costs
Optimize volume
Reduce the reaction time

What is the advantage of this project’s bioreactor?
Due to it uses genetically modified bacteria to transform glucose to PLA, which is released to the culture, it is not necessary to kill these bacteria to get PLA, because in this project, PLA is purified and characterized after its production within bacteria. That’s why the most important advantage of this bioreactor, over chemical bioreactor, is an environmental friendly reactor, because it does not pollute a lot the air, water neither land .
Besides, bacteria do not need to grow in an environment with high temperatures(between 28-30ºC [3]) or pressures, then the bioreactor does not use a great amount of energy (electrical energy or heat, comparing with the temperatures of chemical reactor that are about 130ºC [4]), being a low cost reactor.
In conclusion, this bioreactor is a sustainable equipment.

Equations related to bioreactor
Before writing the equations, it’s important to understand what is happening inside the bioreactor. That’s why a mass balance for the system is showed [2]:

$\left\{\begin{array}{c}Mass accumulated\\ within \\ system\end{array}\right\}=\left\{\begin{array}{c}Mass in \\ through the \\ system \\ boundaries\end{array}\right\}-\left\{\begin{array}{c}Mass out \\ through the\\ system\\ boundaries\end{array}\right\}+\left\{\begin{array}{c}Mass generated\\ within \\ system\end{array}\right\}-\left\{\begin{array}{c}Mass consumed\\ within \\ system\end{array}\right\}$

An example of a bioreactor, is a CSTR (continuous stirred-tank reactor) where the feed rate is equal to outflow, maintaining a constant culture volume. In figure 1 is showed a diagram of a CSTR.

Figure 1. Diagram of a CSTR. Where $F_i = Feed rate; C_{Ai}= Feed concentration ofthe component A; p_i= feed density; F_o = outflow concentration; C_{Ao}=outflow concentration; p_o= outflow density$

Then, considering the mass balance, we can write the following equations [5]:

Global mass balance
$\frac{d({\rho }_o*V)}{dt}=F_i*{\rho }_i-F_o*{\rho }_o$ (1)
Where:
$\begin{array}{l}{\rho }_o = culture density (kg/m^3 )\\ V = culture volume (m^3)\\ F_i = feed rate (m^3 / h)\\ {\rho }_o = feed density (kg/m^3 )\\ F_o = outflow (m^3 / h)\\ {\rho }_o = outflow density (kg/m^3 )\end{array}$ Supposed:
Constant density all the time $({\rho }_o={\rho }_{i })$
Constant volume all the time
Steady state

In conclusion, we have:
$F_i=F_o=F$ (2)
For next equations, it’s supposed the following scheme showed in the figure 2:


Figure 2. Scheme of the bioreactor. The substrate is glucose and the product is PLA. Within bioreactor are the two genetically modified bacteria.

Cell balance

$F*X_i-F*X_o+ \mu *X_o*V-\alpha *X_o*V=\frac{d\left(X_o*V\right)}{dt}=X_o*\frac{dV}{dt}+V*\frac{d{X}_o}{dt}$ (3)
Where:
$\begin{array}{l}{X}_{i,o} = cell concentration (kg/m^3) (feed rate and outflow)\\ \mu = specific growth rate of the bacteria (1/h)\\ \alpha = death rate of the bacteria (1/h)\end{array}$

Supposed:
Constant volume all the time $(\frac{dV}{dt} = 0)$
Steady state $( \frac{dx}{dt}=0)$
There are not cells in the feed $(x_o)$
Death rate(α) is less than the specific growth rate(µ)

Then we have:
$-F*X_o+\mu *X_o*V=0 F*X=\mu *X *V$ (4)
$\frac{F}{V}=\mu$ (5)
And we know that the dilution is $D =F/V D=\mu$

Substrate balance
$F*G_i-F*G_o-\frac{\mu *X_o*V}{Y_{\frac{X}{G}}}-m_S*X_o*V-\frac{q_P*X_o*V}{Y_{\frac{P}{G}}} =\frac{d\left(G_o*V\right)}{dt}=G_o*\frac{d\left(V\right)}{dt}+V*\frac{d\left(G_o\right)}{dt}$ (6)
Where:
$\begin{array}{l}{G}_{i,o} = glucose concentration (feed rate and outflow)(kg/m^3)\\ \mu = specific growth rate (1/h)\\ X_o = cell concentration ( kg/m^3)\\ Y_{\frac{X}{G}} = conversion of cell referred to consumed glucose ( kg cell / kg glucose )\\ m_S = maintenance coefficient(1/h) \\ q_P= specific product formation rate (kg product/ kg cell / h) \\ Y_{\frac{P}{G}}= conversion of product referred to consumed glucose ( kg product/ kg glucose )\end{array}$

Supposed:
1. $m_S* X_o << \mu *X_o$
2. Steady state $$( \frac{d\left(V\right)}{dt}=0 y \frac{d\left(G_o\right)}{dt}=0 )$$

Then we have:
$F*G_i-F*G_o-\frac{\mu *X_o*V}{Y_{\frac{X}{G}}}-\frac{q_P*X_o*V}{Y_{\frac{P}{G}}} =0$ (7)
Dividing by:
$\frac{F}{V}*(G_i-G_o)-X_o * ( \frac{\mu }{Y_{\frac{X}{G}}}-\frac{q_P}{Y_{\frac{P}{G}}} ) =0$ (8)
Using equation 5:
$X_o=\frac{\mu *(G_i-G_o)}{ ( \frac{\mu }{Y_{\frac{X}{G}}}-\frac{q_P}{Y_{\frac{P}{G}}})}$ (9)
Product balance
$F*PL{A}_i-F*PL{A}_o+q_{PLA}*X_o*V=\frac{d\left(PLA*V\right)}{dt}$ (10)
Where:
$\begin{array}{l}PL{A}_{i,o} = PLA concentration(kg/m^3) (feed rate and outflow)\\ q_{PLA}= specific PLA formation rate (kg product/ kg cell / h) \end{array}$
Supposed:
1. There is not PLA in feed rate $(PL{A}_i =0)$ 2. Steady state $\left( \frac{dPLA}{dt} =0 \right)$ 3. $q_{PLA}$ known(experimental data)

Then we have:
$q_{PLA}*X_o*V= F*PL{A}_o$ (11)

For instance, if we want to produce a $F*PLA (Kg/h)$ known, we will be able to calculate the culture volume using the equation 11:
$V=\frac{ F*PL{A}_o}{q_{PLA}}*X_o$

Is this PLA as good as the standard PLA?

After the production of PLA, we have to purify and characterize our polymer to know the most important characteristics of it. So, we’ll use the following protocol to purify and characterize PLA.

Protocol to purify PLA

Recovery of secreted PLA. This protocol is carry out according to a similar protocol used to recover PHB [6]:
1. At 24 and 48 hours, from the beginning of the culture, add CaCl2 till get a concentration of 0,01M within system. Then mix them by inverting the tube several times.
2. Let tube rest for 10 minutes at room temperature and centrifuge it at 54g for 5 minutes.
3. Remove the supernatant and transfer it to a fresh tube, then freeze dry the pellet.
4. Centrifuge the supernatant (in the fresh tube) at 3452g for 10 minutes and freeze dry the pellet.
In conclusion, PLA and CaCl2 are in the pellet from the first centrifugation and the pellet from the second centrifugation contains bacterial mass and non-secreted PLA.
After having the purified PLA, it is necessary characterize it. Thus, the group used the next protocol.

Protocol to characterize the purified PLA

To see functional groups it will be required an IR Transmission (because the necessary equipment to do this characterization is in FCFM) and to evaluate thermal parameters will be required a DSC analysis. The protocol to follow is divided in three steps: the first step is necessary to dry PLA to ensure the elimination of moisture traces and to avoid any undesirable hydrolysis reaction [5], the second step is making a PLA film and the final step is characterize.

Removing moisture
Dry PLA in an oven heating it at 98°C for 3 hours.

Making a PLA based film
PLA based film with thicknesses between 20 and 60 µm was obtained by extrusion with the adequate filming die. Screw speed at 100 rpm was used to optimize the material final properties, while the temperature profile was set up at 180-190-200 °C in the three different extruder heating zones to ensure the complete processing of all systems. The total processing time was established at 6 min. Neat PLA was mixed for 6 min[5].

IR
Infrared spectroscopy analysis was performed at room temperature in transmission and reflection modes by using a spectrometer (from FCFM) at a wavenumber range 4000-400 cm-1[7].

  Thermal analysis (DSC)
Tests were performed from 25 °C to 200 °C at 10 °C min-1 under nitrogen flow rate, with two heating and one cooling scans. The first heating scan was used to erase all thermal history. All measurements were performed in triplicate and data were reported as the mean value ± standard deviation[7].

References

[1]Améstica, Luis. 2013. BIOREACTORES 2013.[Slides]
[2] Pauline M. Doran. 1995. Bioprocess Engineering Principles. San Diego, U.S.A. Academic Press. 257p.
[3] M. Gumel, M. Annuar , Y. Chisti. Recent Advances in the Production, Recovery and Applications of Polyhydroxyalkanoates. [online] http://download.springer.com/static/pdf/755/art%253A10.1007%252Fs10924-012-0527-1.pdf?originUrl=http%3A%2F%2Flink.springer.com%2Farticle%2F10.1007%2Fs10924-012-0527-1&token2=exp=1442075234~acl=%2Fstatic%2Fpdf%2F755%2Fart%25253A10.1007%25252Fs10924-012-0527-1.pdf%3ForiginUrl%3Dhttp%253A%252F%252Flink.springer.com%252Farticle%252F10.1007%252Fs10924-012-0527-1*~hmac=82054d4c4e0398948ab429d62a1fc0d87abe11f525673e4e785bddc44698801a [consulted: 12-09-2015]
[4] Garlotta, 2001. A Literature Review of Poly(Lactic Acid). Journal of Polymers and the Environment, Vol. 9, No. 2.
[5] Lienqueo, María Elena. 2015. Diseño de Bio-reactores, Cultivos continuos, Fermentación e Igeniería Metabólica.
[6] Asif Rahman, Elisabeth Linton, Alex D Hatch, Ronald C Sims and Charles D Miller: Secretion of polyhydroxybutyrate in Escherichia coli using a synthetic biological engineering approach. Journal of Biological Engineering 2013,7:24.
[7] Ilaria Armentano, Elena Fortunati, Nuria Burgos, Franco Dominici, Francesca Luzi, Stefano Fiori, Alfonso Jiménez, Kicheol Yoon, Jisoo Ahn, Sangmi Kang, José M. Kenny, Bio-based PLA_PHB plasticized blend films: Processing and structural characterization, LWT - Food Science and Technology, Volume 64, Issue 2, December 2015, Pages 980-988, ISSN 0023-6438, http://dx.doi.org/10.1016/j.lwt.2015.06.032.