Protocols

Purification

Transformation (bacteria)

Transformation (yeast)

Gel electrophoresis

TBE stock 10X (1000ml)

• 108g Trisbase
• 55g Boric acid
• 9.3g EDTA (Ethylenediaminetetraacetic acid)
• dH20

1. Add the ingredients into 900ml of dH20, mix it properly and fill to 1000ml.
2. Store at room temperature.

NaOH stock 0,1M (200mL)

• 0.8g NaOH
• Boric acid
• dH20

1. Add the ingredients into 200ml of dH20.
2. Set pH on 8,5 by Boric acid.
3. Store at room temperature.

Electrophoresis gel (100ml) 1%

• Agarose
• 1X TBE or 0,1M NaOH
• Ethidium bromide

1. Add 0,7g agarose to 100ml 1X TBE or 10mM NaOH. 2. Heat in microwave for 1 min at high power. 3. Mix it and put it again into microwave for 1 min at high power. 4. Make sure you have nitril gloves. 5. Let it chill down for 6min and add 4 uL of ethidium bromide. 6. Pour the balanced plate, don't forget to put the rake on. 7. After the gel congeal, cover it with 1X TBE or 10mM NaOH.

For making small electrophoresis use half the amounts.

Miniprep

Restriction digest

For a restriction digest of 500ng DNA, you need

• Restriction enzymes
• Corresponding NEB buffer
• 100X BSA
• XμL DNA (500ng)
• (42.5-X)μL dH₂O
• 0.6mL tube

Protocol:

1. Add appropriate amount od dH₂O to the tube
2. Vortex NEB buffer and add 5μL
3. Vortex BSA and add 0.5μL (no need to add BSA when using NEB CutSmart buffer)
4. Vortex DNA and add appropriate amount to the tube
5. Vortex each enzyme and add 1μL to the tube
6. Incubate at 37°C for 30min, then heat-inactivate at 80°C for 20min
7. Store at 4°C

DNA Ligation

Insert mass in ng = \(3\frac{Insert\,length\,in\,bp}{Vector\,length\,in\,bp}Vector\,mass\,in\,ng\)

• 10X T4 ligase buffer
• 0.5uL T4 ligase
• Purified insert and vector (~50ng vector) DNA
• (8.5 - vector and insert)uL ultrapure dH₂0
• 0.6mL tube

Protocol:

1. Add appropriate amount of ultrapure water to sterile 0.6mL tube.
2. Vortex 10X T4 ligase buffer and add 1uL to the tube.
3. Add appropriate amount of vortexed insert and vector DNA to the tube.
4. Vortex T4 ligase and add 0.5uL to the tube.
5. Place the tube in thermal cycler and run ligation protocol (60min incubation at 16°C, 10min at 65°C to denaturate the ligase)
6. Store at -20°C

Band-stab PCR

Excellent technique when you want to amplify specific band from a gel. http://bitesizebio.com/13512/pcr-rescue/ More info..

• Prepare a complete 50μL PCR reaction without DNA template
• Take a sterile pipette tip and stab the desired band of interest 2-3 times
• Swirl the tip in the tube with prepared PCR reaction
• Run the PCR as usual

Gibson

Genome extraction

Soft lithography - PDMS molding

• Mix 40g of PDMS with 4g of curing agent
• Centrifuge the mixture at 3250 RPM for 3 minutes to remove the bubbles introduced during the mixing
• Clean silicon master with air gun
• Wrap an aluminium foil around the edges of the silicon master to create a container
• Pour the PDMS mixture over the silicon master
• Cure the PDMS in an oven at 80°C for 2 hours
• Leave the PDMS to cool down
• Detach the PDMS carefully from the silicon master

Soft lithography - Bonding PDMS-Glass

Preparation of the substrates

Glass slide

• Rinse the glass slide with acetone, isopropanol, and deionized water
• Dry the glass slide with air gun
• Dehydrate the glass slide on a hot plate at 120°C for 30 minutes

PDMS

• Slice the PDMS to individual PDMS replicas
• Drill holes for microfluidic inlets and outlets
• Clean the PDMS using a scotch tape

Air plasma treatment

• Place the glass slide and the PDMS replicas into a plasma cleaner, contact surfaces facing upwards
• Exhaust the atmosphere with a vacuum pump and wait until the pressure drops to 500 mTorr
• Activate the plasma for 2.5 minutes at Hi power
• Stop the plasma and open the valve to stabilize the pressure, continue immediately with the bonding phase

Permanent irreversible bonding

• Place the PDMS replica on the glass slide
• Place the bonded device in an oven at 80°C for 60 minutes.
• Seal the inlets and outlets with a scotch tape until use