Difference between revisions of "Team:UC Davis/Safety"

Line 210: Line 210:
  
 
                                                                                                                                                                                                                                   <!--PUT CONTENT HERE-->
 
                                                                                                                                                                                                                                   <!--PUT CONTENT HERE-->
 +
<div>
 +
  <input type="checkbox" class="read-more-state" id="post-1" />
 +
  <p class="read-more-wrap">
  
 
<b><u>Preparation of DNA for Cloning</u></b>
 
<b><u>Preparation of DNA for Cloning</u></b>
Line 215: Line 218:
  
 
                                                                                                                                                                                                   <!------ TO ACTUALLY USE SHOW MORE-------->
 
                                                                                                                                                                                                   <!------ TO ACTUALLY USE SHOW MORE-------->
<div>
+
 
  <input type="checkbox" class="read-more-state" id="post-1" />
+
  <p class="read-more-wrap">
+
 
<span class="read-more-target">
 
<span class="read-more-target">
 
Originally, our cloning method was to be Gibson assembly. We ordered our 8 genes with 5’ and 3’ gibson overhangs from IDT. Once received, we rehydrated the genes: <br>
 
Originally, our cloning method was to be Gibson assembly. We ordered our 8 genes with 5’ and 3’ gibson overhangs from IDT. Once received, we rehydrated the genes: <br>
Line 232: Line 233:
  
 
</span></p>
 
</span></p>
  <label for="post-1" class="read-more-trigger"></label>
+
  <label for="post-1" class="read-more-trigger"></label>
 +
 
</div>
 
</div>
  

Revision as of 21:06, 18 September 2015



In the Laboratory
At the beginning of summer everyone on our team took the online UC Fundamentals of Laboratory Safety course. This course described correct use of personal protective equipment and engineering safety controls within the lab to reduce risks associated with each lab space. The course also covered methods involved in chemical safety including the identification of chemical hazards through the use of Material Safety and Data Sheets (MSDS) and pictograms as well as proper chemical storage and disposal. In addition to this general safety course, we were also trained on the laboratory specific hazards by the lab managers of the three spaces that we worked in.

Since our project involved use of some proteins found in known pathogens, we decided to synthesize the genes we were interested in through IDT to express in laboratory E. coli. These safety precautions ensured that we 1. did not culture pathogenic organisms in the laboratory and 2. the proteins we expressed were not toxic or pathogenic. To ensure that our engineered strains did not exit the lab, we killed all of our cultures with 10% (v/v) bleach before disposal. We also did not transport any engineered strains outside of the lab, reducing the risk of release.

Our project involved the use of an array of small molecules. To ensure safety, we followed recommendations in the MSDS for each of the chemicals that we used. When ordering our library of alternate FabI substrates, we made sure not to order chemicals that were acutely toxic. For the chemicals we tested, we followed the MSDS recommendations for proper use of personal protective equipment including, wearing eye protection, lab coats, and wearing rubbing gloves, and engineering controls such as a working in the fume hood to eliminate the risk of chemical exposure.

Since the inhibitor we are detecting, triclosan, is toxic, we created a triclosan waste container to avoid dumping triclosan down the drain. The proper way to dispose of this container is to give it to UC Davis’s Environmental Health and Safety Services

In the Real World
The risk our project might pose in the real world is the handling of hazardous substrates. We've discovered non natural substrates to use on our enzyme sensor, but the molecules we've found are somewhat hazardous. As a product, if all of the reagents would need to be self contained and never in direct contact with the user. To reduce such risk, we might want to screen for other less hazardous substrates.

        ↥


Preparation of DNA for Cloning


Originally, our cloning method was to be Gibson assembly. We ordered our 8 genes with 5’ and 3’ gibson overhangs from IDT. Once received, we rehydrated the genes:

  1. Centrifuge for 3-5 seconds at >3000 x g to pellet at the bottom
  2. Add 20 uL TE buffer or Milli-Q water for a final concentration of 10ng/uL
  3. Briefly vortex and centrifuge
  4. Store at -20 degrees for up to 24 months with TE buffer or 1 month with dH2O

We made four 50 mL and four 2 mL overnight cultures of DH10B containing pET29b+ vector for insertion with kanamycin resistance selection. The grown 50 mL cultures were then transferred to 50 mL falcon tubes and spun down to pellet at 4000 x g for 10 minutes. We then followed the protocol included in the Invitrogen MaxiPrep kit used. The results gave an average of 1.93 ng/uL, which is below the threshold for accurate concentration measurement for the Biotek Epoch spectrophotometer with the Take3 Microvolume plate. This also showed that the results yielded next to no DNA for the MaxiPrep and decided to go forth with a MiniPrep on the four 2 mL cultures using the Invitrogen MiniPrep protocol provided with the kit. The results yielded an average of 90 ng/uL which is above the 60-80 ng/uL concentration needed for the restriction digestion.

Continue scrolling to read more or click here to advance to the next section!

TITLE HERE!!!!!


PUT YOUR TEXT HERE!!!!!!

Continue scrolling to read more or click here to advance to the next section!

TITLE HERE!!!!!


PUT YOUR TEXT HERE!!!!!!

Continue scrolling to read more or click here to advance to the next section!

Sources:


        ↥
  1. First bullet point
  2. Second bullent point


Continue scrolling to read more or click here to advance to the next section!

Sources:
        ↥
  1. First bullet point
  2. Second bullent point


Continue scrolling to read more or click here to advance to the next section!

Sources:
        ↥
  1. First bullet point
  2. Second bullent point


Sources:
        ↥