Revision as of 01:38, 19 September 2015

Design

While there are many genetic switches for detecting proteins, for example, the lac operon and tet regulators, to our knowledge, every genetic switch is unique to the protein it detects. Aptapaper seeks to create a switch that could have the same logic adapted to any protein, similar to how toehold switches can be adapted and respond to any sequence of trigger RNA. Toehold switches refer to an RNA switch that works by sequestering the ribosomal binding site and start codon in a hairpin, while leaving a portion of what the RNA trigger binds to exposed in a “toehold” region. This toehold region dramatically changes the kinematics of the system, making it much easier for the trigger to bind. After the initial binding, the hairpin is “unzipped” by the trigger¹. Exact design specs of the well optimized second generation toehold design are detailed in Figure 1. Because toehold switches can respond to any RNA trigger, Aptapaper attempted to use aptamers in conjunction with toehold switches to allow efficient and sensitive protein sensing. See different design approaches below.

Switch 1.0 - Trigger-Aptamer Release for Toehold

In this design, a DNA trigger is bound by a DNA aptamer and “junk” DNA. The aptamer binds the protein of specificity when it is present, displacing the trigger, which can then activate the toehold switches previously discussed. While the system was based on the same DNA release sequence as validated for protein detection via fluorophore unquenching (FRET)², the 5’ 3’ orientation is reversed so that no part of toehold region is unbound when hybridized to the trigger. The toehold region of the switch used in our system is also 12nt instead of the 15nt seen in forward engineered switches for the same reason. Additionally, this design used a DNA trigger to activate the RNA switch, a previously untested configuration.

Because the toehold binding region of the trigger is complementary to the aptamer, this design necessitates that an RNA sequence identical to a portion of the DNA aptamer is exposed in the toehold region of the switch. It was unclear if the RNA version of the DNA aptamer would maintain some affinity for thrombin. The results (link) from this design suggest that the toehold region may in fact be functioning as an aptamer, which immediately suggests the two designs seen below. Switch 1.1 - Trigger-Aptamer Release for Toehold This design follows the same general strategy as Switch 1.0, but is adjusted so that the toehold region of the switch is not the same sequence as the aptamer bound by the trigger. Multiple versions of Switch 1.1, including some inspired by Team Heidelberg collaboration have been ordered, but switch is untested at the time of writing.

Switch 2.0 - Toehold with Protein “Trigger”

This design takes advantage of the aptamer in the toehold and hairpin regions of the switch by having the protein intentionally bind to this region, acting like a trigger to unfold the hairpin. In Switch 2.0, the 3’ end of the aptamer ends at the start of the ribosome binding site bubble, extends into the 15nt hairpin, and then the remainder of the aptamer forms the toehold region. The hairpin was destabilized from the forward engineered design by shortening the hairpin from 18nt to 15nt and adding 3nt to the ribosome binding site loop. One important parameter which must be optimized in this design is the number of bases in the aptamer which are exposed in the toehold region. If too much aptamer is exposed the protein could bind without unfolding the hairpin; too little, however, and the protein may not bind at all. Additionally, the hairpin structure could be too weak to stay bound under the low salt, high temperature conditions suited for in vitro translation. Additionally, depending on the way the aptamer recognizes the protein, a 3D structure critical for protein detection could be sequestered in the hairpin. Despite these concerns, the switch worked well for one protein thus far (results LINK), with another currently being tested.

Switch 2.1
In this design, the hairpin is lengthened by 3nt to the 18nt seen in the forward engineered switches, making it more stable to reduce background protein translation. DNA sequences have been ordered, but switch is untested at the time of writing.

Switch 3.0
Called proximity dependent ligation, this design involves two aptamers binding to different regions of the same protein of specificity. This somehow enables translation induction. DNA sequences have been ordered, but switch is untested at the time of writing.

Reaction Conditions

Temperatures ideal for hybridization of short DNA oligos are lower and salt concentrations are higher than that recommended for in vitro translation. The trigger and aptamer likely did not bind, allowing uninhibited switch induction in the negative controls. In order to find conditions that acceptable for in vitro translation that also allow hybridization of short DNA oligos, higher salt concentrations are currently being tested with a control switch. Lower temperatures will also be tested, time permitting.