Latest revision as of 00:00, 19 September 2015

Media/Buffer

LB Medium

- Add the following components

NaCl	10 g
Yeast extract	5 g
Tryptone	10 g
H₂O	ad. 1000 mL

To obtain solid media add 15g/L agar.

- Autoclave at 121 ^oC for 20 min.

- The preferred antibiotic is added from a concentrated stock solution to an appropriate concentration (e.g Ampicilin is added to a final concentration of 100 µg/ml).

To the liquid medium antibiotic is added upon usage.
For the preparation of agar plates antibiotic is added after autoclaving the media and cooling it to 60 ^oC.

"Fat" LB Medium

Fat medium was used as culture medium for the induction of our cultures

Yeast extract	40 g
KH₂PO₄ (MW: 136.09)	7.0 g
Na₂HPO₄ x 12 H₂O (MW: 358.14)	15.14 g
H₂O dest.	ad. 1000 mL

pH 6.8 with NaOH (ca. 10mL 1M NaOH)

After autoclaving add:

50% Glycerine (sterile)	14 mL
24% MgSO₄ x 7 H₂O (sterile)	7.5 mL

Media and Culture Methods for Dockerin Organisms of Origin

Pseudobacteroides cellulosolvens

DSMZ Medium 315

Clostridium cellulolyticum

DSMZ Medium 520

Clostridium thermocellum

DSMZ Medium 122

Acetivibrio cellulolyticus

DSMZ Medium 165

DSMZ Medium 141

Phosphatase Activity plates, Sperber media

A: Stock reagents

1M IPTG (4.76 g in 20ml Millipore-H2O) filter with blue 0.22 µm sterile filter and freeze at -20˚C

50mg/ml Kanamycin in Millipore H2O, filter with blue 0.22 µm sterile filter and freeze at -20˚C

100mg/ml Ampicillin in 50% ethanol, filter with blue 0.22 µm sterile filter and freeze at -20˚C

25mg/ml BCIP (in DMF) filter with blue 0.22 µm sterile filter and keep in a falcon tube wrapped with aluminum foil at 4˚C. BCIP: Biomol Nr. 2291 (MG 433.64)

Glycerol (99%), autoclaved and kept at room temperature

B: Sperber medium

1g Yeast extract

3.5 ml 50% w/w Phytic acid

0.2 g CaCl2

0.5 g MgSO4

Adjust the pH to 7.2 with NaOH

Ad 2 L of Millipore H2O

32 g agar

Autoclave

After autoclaving the medium must cool down to ca. 50˚C. Now glycerol, IPTG, BCIP and the respective antiobiotic can be added.

For 2 L medium:

2 ml BCIP

2 ml 1M IPTG

2 ml Ampicllin or Kanamycin

40 mL Glycerol

The media is now ready for plating

Result: On Sperber medium phosphatase-recombinant colonies should develop a distinct color blue after 2 days.

Esterase Activity plates, with 1% Tributyrin

To 500 ml of LB Media add 7.5 g of Agar and 5 ml of Tributyrin and homogenize with a mixer.

This culture medium must be directly sterilized by autoclaving at 121˚C for 20 min.

If you wait too long it will be inhomogeneous again!

When the medium cools down to 50°C, the antibiotic can be added.

Result: Halo formation is visible around the positive clones.

Cellulase activity plates

A: LB_ agar base

Add the following components

Yeast extract	5 g
Tryptone	10 g
NaCl	10 g
H₂O	Add to 1 L
Agar	15 g

Make sure to put a stirrer in the bottle.
Sterilize the culture medium by autoclaving at 121 ^oC for 20 min.

B: Substrate for cellulase screening

In 15 ml falcon tube, the substrate with final concentration 1% (w/v) is prepared in 96% (v/v) ethanol. For-example, to prepare 10 ml stock solution, weight 0.1 g of AZCL-HE-Cellulose and transfer it to 15 ml falcon tube, then add 96% (v/v) ethanol until the volume reached 10 ml.

The stock solution will be stored at +4 °C.

C: Prepare the agar plates

When the medium cools down to around 60 °C, put the bottle containing LB-agar base on a magnetic mixer. At the same time, disperse the substrate by flip the falcon tube several times. Then, pour the substrate into the LB-agar base gently until the substrate suspend evenly in the agar medium (For how much substrate should be poured, ask the supervisor). Other reagents like antibiotic can also be added. Ca. 3-5 ml substrate per Liter medium.

D: Preparation of agar plates contacting cellulose substrate

After dispersing substrate and adding antibiotic to LB-agar , pour the medium quickly with continuous stirring onto the plates and make sure to make a thin layer of medium. Let the plates to dry and store them at 4 °C.

E: Another method of pouring Substrate for cellulase screening on to the agar plates

Rather than using normal pouring method one can first prepare regular LB plates having just a thin layer of LB. After preparation of substrate for cellulase screening add the proper antibiotic to it and then pour this mixture on top of this thin LB layer with constant stirring. Let the plates to dry and then store at 4 °C.

1x TAE Buffer

1 x TAE Buffer

Tris	24.22 g
Acetic acid (100%)	5.74 ml
EDTA (0.5M, pH 8.0)	10 ml
H₂O dest.	ad. 5 L

Cloning Methods

PCR product purification using QIAquick® PCR Purification Kit (QIAGEN)

Add ethanol (96–100%) to Buffer PE before use.
All centrifugation steps are carried out at 17900 g in a conventional table-top microcentrifuge at room temperature.

- Add 5 volumes Buffer PB to 1 volume of the PCR reaction and mix.

- Place a QIAquick column in a provided 2 ml collection tube.

- To bind DNA, apply the sample to the QIAquick column and centrifuge for 30–60 s. Discard flow-through and place the QIAquick column back in the same tube.

- To wash, add 0.75 ml Buffer PE to the QIAquick column, centrifuge for 30–60 s. Discard flow-through and place the QIAquick column back in the same tube.

- Centrifuge the QIAquick column once more in the provided 2 ml collection tube for 1 min to remove residual wash buffer.

- Place each QIAquick column in a clean 1.5 ml microcentrifuge tube.

- To elute DNA, add 50 μl water (40 – 60 ^oC) to the center of the QIAquick membrane, let the column stand for 1 min, and then centrifuge for 1 min.

PCR Gel extraction, peqGOLD Gel Extraction Kit

- Fractionate DNA fragments by running a agarose gel (Do not stain the gel with Ethidium bromide or expose the DNA to UV for too long).

- Add equal volume of Binding Buffer to the gel slice and incubate at 65ᵒC for 8 min. Vortex or mix every 2 to 3 min until the agarose dissolves completely. (0.2 g of gel equivalent to 0.2 ml)

- Pour the mixture into PerfectBind DNA column (which is placed in a 2 ml collection tube) and centrifuge for 1 min at 10000 x g.(max. 750 µl) Discard the flow-through and place the PerfectBind DNA column in the same tube. Repeat the steps if required.

- Add 300 µl of binding Buffer to the PerfectBind DNA column for the washing the contaminants and centrifuge for 1 min at 10000 x g. Discard the flow-through and place the column in the same tube

- Add 750 µl of CG Wash Buffer to the PerfectBind DNA column for the wash, incubate for 2 to 3 min and centrifuge for 1 min at 10000 x g. Discard the flow-through and place the column in the same tube. Repeat this step once more.

- Centrifuge the PerfectBind DNA column once more in the 2 ml collection tube for 1 min at 10000 x g to remove the residual wash buffer.

- Place the PerfectBind DNA column in a clean 1.5 ml eppendorf tube.

- Add 50 µl of pre-warmed sterile water to the PerfectBind DNA column and incubate for 2 to 3 min (normally in a 2 step process of 30 µl in first elution step and 20 µl in second elution step) and centrifuge at 5000 x g for 1 min.

- Store the purified DNA at -20ᵒC.

Blunt End Ligation in pJET1.2 vector –Clone JET PCR Cloning Kit– (Thermo Scientific)

- Set up the following componentson ice for the ligation reaction.

Components	Volume
2x Reaction buffer	10 µl
Blunt end PCR product	125 ng
pJET 1.2 Plasmids	50 ng (1µl)
T4 DNA Ligase	1 µl
Water(RNase free)	x µl
Total Volume	20 µl

- Vortex briefly and centrifuge for 3-5 sec at 5000 rpm.

- Carry out the ligation at 20°C for 20 min at room temperature (22-25°C) and then place in ice for 5 min and use for transformation immediately or store at -20°C.

Cloning principle:

pJET1.2 is a linearized cloning vector designed for inserts from 6 bp to 10 kb. The 5’-ends of the vector contain phosporyl groups, therefore phosphorylation of the PCR products is indicated.

Optimal insert/vector ratio is 3:1. (0.15 pmol ends of insert and 0.05 pmol ends of vector)

Optimal PCR product quantity for ligation reaction is to be calculated from the Kit protocol, For the length of 2.5 kb of PCR product, to have 0.15 pmol ends of the PCR product in the ligation reaction 125 ng of the PCR product should be used.

For PCR products more than 3 kb, ligation can be prolonged to 30 min.

Sticky End T4 Ligation (Thermo Scientific)

T4 Ligation - Thermo Fisher Scientific - sticky end ligation

1. Prepare the following reaction mixture:

Linear vector DNA	20 ng
Insert DNA	80 ng
10x T4 DNA Ligase buffer	2 µl
Thermo Scientific T4 DNA Ligase (Cat #EL0016)	1 U
Nuclease free H₂O	Add to 20 µl

2. Incubate 1 hour at RT

3. Heat inactivation of T4 DNA Ligase at 65 °C for 10 minutes or at 70 °C for 5 min

TOPO® Cloning protocol usingChampion™ pET Directional TOPO® Expression Kits (Thermo Fisher Scientific)

You will perform TOPO® Cloning in a reaction buffer containing salt. Note: the amount of salt added to the TOPO® Cloning reaction has to be adapted to the planned transformation protocol (chemically competent cells or electrocompetent cells).

- Set up the TOPO® Cloning reaction depending on the transformation method.

Reagents	Chemically Competent E. coli	Electrocompetent E. coli
Fresh PCR product	0.5 to 4 μl (15 – 40 ng)	0.5 to 4 μl (15 – 40 ng)
Salt Solution	1 μl	---
Dilute Salt Solution (1:4)	---	1 μl
Sterile water	add to a final volume of 5 μl	add to a final volume of 5 μl
TOPO® vector 1	1 μl (15 – 20 ng)	1 μl (15 – 20 ng)
Total Volume	6 μl	6 μl

- Mix reaction gently and incubate for 15 - 30 minutes at room temperature (22-23°C).

- Place the reaction on ice and proceed with the transformation or store at - 20 °C.

Before transformation into electrocompetent E.coli the salt is removed via microdialysis. For more information refer to transformation in electrocompetent BL21 E.coli.

Plasmid transformation into chemically competent E. coli

- Thaw chemically competent E.coli cells (BL21 or TOP10) on ice.

- Add 100 – 250 ng of ligation product. Mix gently, do not pipette up and down.

(add 30 – 60 ng pET 101 construct depending on the cloning protocol).

- Place on ice for 5 – 15 min.

- Heat shock 45-50 seconds at 42 °C.

- Incubate 2-5 min on ice.

- Add 300 - 500 μl of LB medium.

- Incubate at 37°C for 1 hour with shaking.

- Plate 100 – 150 μl on prewarmed LB plate containing the proper antibiotic. Centrifuge the rest for 2 min at 5000 xg. Decant the supernatant and move the tube against hard surface to suspend the pellets in the residual medium. Plate the cells on another LB plate containing the proper antibiotic.

- Incubate LB plates at 37°C overnight.

- Check plates for colonies growth.

For positive control set up another transformation using an equal amount of a circular plasmid possessing the proper antibiotic resistance.

Electroporation of BL21 cells with pJET_RFP

- Apply microdialysis for 30 -45 min by applying the transformation mixture (plasmid+buffer) on (Millipore® MF-Millipore™ DNA Fillter Paper for Dialysis of DNA and Proteins – capitol scientific) after placing the membrane on sterile water.

- Defreeze 40 µl aliquots of chemically competent cells on ice

- Mix 50-200 ng DNA with the cells. (desalted)

- Transfer the culture without any air bubbles into pre-cooled electroporation cuvettes (40 µl maximum) and incubate on ice for 10 minutes.

- Electroporate using the electroporator with 1.25 mV, 5 decharge time.

- Immediately after electroporation, transfer 300 µl room temperature LB medium on top of the cells and transfer it into an 1.5 ml fresh E-cup

- Incubate the culture for 1 hour at 37°C and 150 rpm

^-Spread a 100 µl from the dilution series (10^-3 to 10^-6) on a pre-warmed LB plate containing ampicillin

^-Incubate the plates overnight at 37°C

Plasmid Extraction - using QIAprep Spin Miniprep Kit (QIAGEN)

This protocol describes the purification of plasmid DNA from 5 ml overnight cultures of E. coli grown in LB medium using the QIAprep Spin Miniprep Kit (QIAGEN)

Add the provided RNase A solution to buffer P1, mix, and store at 4 ^oC.
Add ethanol (96–100%) to Buffer PE before use.
All centrifugation steps are carried out at 17,900 x g (13,000 rpm) in a conventional table-top microcentrifuge at room temperature.

- Add the proper antibiotic with the proper concentration to 5 ml LB medium (e.g Ampicilin is added to a final concentration of 100 µg/ml).

- Inoculate the medium with the desired E.coli strain and incubate overnight at 37 ^oC with agitation (150 rpm).

- Pellet the overnight culture by centrifugation at 8,000 rpm (6,800xg) for 3 min at room temperature.

- Resuspend pelleted bacterial cells in 250 μl Buffer P1 and transfer it to a microcentrifuge tube.

- Add 250 μl Buffer P2 and mix thoroughly by inverting the tube 4–6 times. Do not allow the lysis reaction to proceed for more than 5 min.

- Add 350 μl Buffer N3 and mix immediately and thoroughly by inverting the tube 4–6 times.

- Centrifuge for 10 min at 17,900 x g in a table-top microcentrifuge.

- Apply the supernatant to the QIAprep spin column by decanting. Centrifuge 60 s. Discard the flow-through.

- Wash the QIAprep spin column by adding 500 μl Buffer PB and centrifuging for 60 s. Discard the flow-through.

- Wash QIAprep spin column by adding 750 μl Buffer PE and centrifuging for 30–60 s.

- Discard the flow-through, and centrifuge for an additional 1 min to remove residual wash buffer.

- Place each QIAquick column in a clean 1.5 ml microcentrifuge tube.

- To elute DNA, add 50 μl water (40 – 60 ^oC) to the center of the QIAquick membrane, let the column stand for 1 min, and then centrifuge for 1 min.

Plasmid Extraction - using peqGOLD Plasmid Miniprep Kit I (PEQLAB Technologies)

Select few TOP10/BL21 E.coli transformed colonies from the LB Amp plates containing the propagated transformed colonies and inoculate them into liquid LB medium (5 ml) containing preferred antibiotic of desired concentration in each tube.

Incubate the LB tubes with the transformed colonies at 37°C in a shaker for about 12 – 15 hours (overnight) with agitation (150 rpm).

Extract the plasmids from the incubated LB cultures using the peqGOLD Plasmid Miniprep Kit I.

Centrifuge the culture at 10,000 x g for 2 min to obtain the pellet and repeat the process until the culture is completely centrifuged. Store the pellet of 1 ml of the culture at -20°C for future use.

Resuspend the pellet in 250 µl of Solution I of the Kit (which is normally kept at 4°C because of the RNase) and vortex until the pellet is resuspended.

Add 250 µl of Solution II to the resuspended mixture and gently mix by inverting and rotating the tubes 6 -10 times to obtain a cleared lysate. Incubate the mixture for 2 min to obtain optimum results.

Add 350 µl of Solution III to the cleared lysate and gently mix by inverting the tubes 6 -10 times until a flocculent white precipitate is formed. Centrifuge at 10,000 x g for 10 min at room temperature.

Transfer the clear supernatant to a fresh PerfectBind DNA Column in a 2 ml Collection Tube. Centrifuge the Column with the Collection Tube for 1 min at 10,000 x g at room temperature. Discard the flow-through liquid.

Add 500 µl of PW Plasmid buffer to the PerfectBind DNA Column in the Collection Tube and centrifuge for 1 min at 10,000 x g. Discard the flow-through.

Add 750 µl of DNA Wash buffer to the PerfectBind DNA Column in the Collection tube and centrifuge for 1 min at 10,000 x g. Discard the flow-through. Repeat this step to obtain optimum results.

Place the PerfectBind DNA Column in the Collection tube and centrifuge for 2 min at 10,000 x g to dry the column matrix. This step is essential to remove ethanol from the column.

Place the PerfectBind DNA Column into a fresh 1.5 ml Eppendorf tube. Add 50 µl of pre-warmed sterile deionized water directly to the binding matrix in the PerfectBind DNA Column and centrifuge for 1 min at 5,000 x g to elute the DNA.

Discard the PerfectBind DNA Column and store the eluted plasmid DNA at -20°C.

Check the concentration of the plasmids by using a NanoDrop and note down the values for future experiments.

Competent Cells

Preparation of competent E.coli cells

Method 1: Low amount of competent cells

Materials:

Buffer RF1 (150 ml): 1.44 g RbCl

1.16 g MnCl₂.4H₂O

3.6 ml Potassium acetate (1M)

pH 7.5 with acetic acid

Buffer RF2 (80 ml): 1.6 ml MOPS (0.5 M) stock solution

pH 6.8 with NaOH

0.096 g RbCl

0.88 g CaCl₂.2H₂O

Procedure

- Inoculate a 4 ml culture either with a single colony or with a cryoculture of the desired E.coli strainand incubate the culture with agitation overnight at 37°C

_-Inoculate a 300 ml shake flask containing 100 ml LB medium with the overnight culture to an OD₆₀₀ of 0.05 and grow the culture at 37°C until the OD₆₀₀is about 0.3

- Transfer the cells into two 50 ml falcon tubes, incubate the cultures for 15 minues on ice and harvest the cells by centrifugation for 15 min at 5,000 rpm and 4°C. Discard the supernatants.

- Resuspend the cells in 1/3 of the original volume (~16 ml/50 ml) of buffer RF1, incubate the cells again on ice and harvest the cells by centrifugation for 15 min at 5,000 rpm and 4°C. Discard the supernatants.

- Resuspend the cells in 4 ml of buffer RF2 and incubate the suspensions for 15 min on ice. Prepare the Eppendorf tubes and liquid nitrogen.

- Put 0.4 ml of the cell suspension into the Eppendorf reaction tubes and freeze the cells by transferring them immediately to the liquid nitrogen. Store the competent cells at -80°C

Method 2 (High amount of competent cells, time consuming)

Materials

TB 3.46 g Piperazine-N,N'-bis(2-ethanesulfonic Acid) Pipes, 11 mM

2.2 g CaCl₂.2H₂O (15 mM)

18.64 g KCl (250 mM)

PH 6.7, autoclave, add 55 ml MnCl₂ (1M, sterile) to a final volume of 1 l

SOB-Mg 20 g/l tryptone (2%)

5 g/l Yeast extract (0.5%)

0.58 g/l NaCl (10 mM)

0.186 g/l KCl (2.5 mM)

SOB SOB-Mg

10 mM MgCl₂

10 mM MgSO₄

LB liquid medium

DMSO (Dimethyl sulfoxide)

Procedure:

- Inoculate a 20 ml culture either with a single colony or with the cryoculture of the desired E.coli strainand incubate the culture with agitation for 20 h at 28°C

- Inoculate a 250 ml SOB medium supplemented in a 2 l shake flask and grow the cells to an OD₆₀₀ of 0.5- 0.9 (20-20 h) at 18°C and 200-250 rpm

- Incubate the whole flask for 10 min on ice. Collect the cells by centrifugation for 10 min at 4°C and 5000 rpm. Resuspend the cells in 80 ml of ice-cold TB and incubate them for 10 min on ice. Collect the cells by centrifugation for 5 min at 5,000 rpm.

- Resuspend the cells in a 20 ml of ice-cold TB. Add DMSO to a final concentration of 7% (1.4 ml) and gently shake the falcon tube.

- Transfer 0.2 ml aliquots into labelled eppendorf reaction tubes and freeze the cells in liquid nitrogen. Store the cells at –80°C.

Transformation Efficiency Kit, RFP construct (iGEM)

Before using our competent E. coli TOP10 cells in the important experiments, we used the Transformation Efficiency Kit to test the efficiency of our competent cells!

The kit includes five vials of each different DNA concentration: 50pg/μl, 20pg/μl, 10pg/μl, 5pg/μl, 0.5pg/μl of purified DNA from BBa_J04450 (RFP construct) in plasmid backbone pSB1C3.

Protocol as distributed by iGEM (modified)

Spin down the DNA tubes from the Transformation Efficiency Kit to collect all of the DNA into the bottom of each tube prior to use. A quick spin of 20-30 seconds at 8000-10000 rpm will be sufficient. Note: There should be 50 µL of DNA in each tube sent in the Kit.

Thaw competent cells on ice. Label one 2.0 ml microcentrifuge tube for each concentration and then pre-chill by placing the tubes on ice.

Pipet 1 µL of DNA into each microcentrifuge tube. For each concentration, use a separate tube.

Pipet 50 µL of competent cells into each tube. Flick the tube gently with your finger to mix. Incubate on ice for 30 minutes. Pre-heat heating block now to 42°C.

Heat-shock the cells by placing onto the heating block for 1 minute.

Immediately transfer the tubes back to ice, and incubate on ice for 5 minutes. This helps the cells recover.

Add 200 µL of LB media per tube, and incubate at 37°C for 1 hour. Prepare the LB-Cam (Chloramphenicol) agar plates during this time: label them.

Pipet 20 µL from each tube onto the appropriate plate, and spread the mixture evenly across the plate. Do triplicates (3 each) of each tube if possible, so you can calculate an average colony yield. Incubate at 37°C overnight. Position the plates so the agar side is facing up, and the lid is facing down.

Count the number of colonies on a light field or a dark background, such as a lab bench. Use the following equation to calculate your competent cell efficiency. If you've done triplicates of each sample, use the average cell colony count in the calculation.

(colonies on plate) / ng of DNA plated x 1,000ng/µg

Note: The measurement "ng of DNA plated" refers to how much DNA was plated onto each agar plate, not the total amount of DNA used per transformation. You can calculate this number using the following equation:

1 µL x concentration of DNA (refer to vial) x (volume plated / total reaction volume)

NOTE: Since this protocol led to a very low transformation efficiency we repeated the experiment with 200 µL competent cells instead of 50 µL and plated 100 µL instead of 20 µL.

Results

Competent cells should have an efficiency of 1.5x10⁸ to 6x10⁸ cfu/µg DNA, where "cfu" means "colony-forming unit" and is a measurement of cells.

Protein Extraction and Purification

Induction, harvest and disruption of expression cultures

Induction

Recombinant protein expression was exclusively realized in E.coli. pET101-ScaA was expressed in BL21(DE3) cells under the control of the lac operon, and pBAD-RFP-ACEL (and all other pBAD constructs) was expressed in TOP 10 cells under the control of the ara operon. The procedure is as follows:

Inoculate “fat” LB expression medium, having a volume corresponding to 5 % of the shake flask that is used, with 5 % (v/v) of an overnight LB starter culture grown at 37°C and 150 rpm.

Incubate the expression culture at 37°C and 150 rpm until an OD₆₀₀ between 2.5 and 3.5 is reached.

Induce protein expression by adding the appropriate inducer to the expression culture. In case of pET101-ScaA use 1 mM IPTG and in case of pBAD-RFP-ACEL use 0.2 % (v/v) L-arabinose.

Incubate the expression culture for 20 h at 37°C and 150 rpm.

Take a 1 ml sample before induction and before cell harvesting in order to analyze the expression effectivity of target proteins by SDS-PAGE.

Cell Harvest

Pellet the culture at 4°C, 13000rpm for 20min (SLA-3000 rotor, Sorvall).

Resuspend and wash with an equal volume of LEW Buffer (see Protein extraction).

Repeat previous centrifugation step.

Freeze pellet until further use or prepare for French Press.

Cell extraction by French Press

Resuspend pellet in 20mL 1x LEW Buffer .

Take a small sample (10µl) for microscopy.

Disrupt cells by using a discontinuous high-pressure homogenizer (e.g., French-Press, 4 cycles at 1000 psi).

take a small sample (10µl) and analyse both before and after press samples under the microscope. Look for inclusion bodies.

Sediment cell debris via centrifugation for 30 min at 13000 rpm (SS-34 rotor, Sorvall) and 4°C.

Filter the resulting supernatant through 0.45 µm sterile filters and subsequently apply it to chromatographic purification steps.

Protein Purification (Protino® Ni-IDA 2000 His-Tag protein purification, Macherey-Nagel)

1 x LEW (Lysis-Equilibrium-Wash) Buffer:

NaH₂PO₄ x 2 H₂O (MW: 156.07 g/mol)	7.8 g
NaCl (MW: 58.44 g/mol)	17.5 g
H₂0 dest.	ad. 1000 mL

Adjust to pH 8.0 using NaOH.

1 x Elution Buffer:

NaH₂PO₄ x 2 H₂O (MW: 156.07 g/mol)	7.8 g
NaCl (MW: 58.44 g/mol)	17.5 g
Imidazole (MW: 68.08 g/mol)	17.0 g
H₂0 dest.	ad. 1,000 mL

Adjust to pH 8.0 using NaOH.

Protino® Ni-IDA 2,000 His-Tag protein purification (Macherey-Nagel)

- Wet Ni-IDA column with 4 mL of 1x LEW buffer and discard flow through

- Run supernatant from the cell extraction through the column and collect flow through (cell extract, store at 4°C)

- Wash column 3 times with 4 mL 1x LEW Buffer

- Collect each flow through (wash 1-3) and store at 4°C

- Elute protein 3 times with 3 mL Elution Buffer (contains Imidazole)

- Collect each elution and store fractions at 4°C

- Quantify protein content by Bradford measurement (see Bradford assay)

Affinity chromatography of His-tagged proteins

The N-terminal His₆- tagged fusion proteins His₆-ScaA and His₆-RFP-ACEL were purified by nickel affinity chromatography using Ni-NTA-agarose columns in a first purification step.

Preparation:

Connect a 5 ml HisTrap FF column (GE Healthcare) to an Äkta purifier or Äkta prime system and wash the column with 1 CV (column volume) 20 % EtOH and a maximum flow rate of 3 ml/min.

Pre-equilibrate the column with lysis buffer by first washing 3 CV with water, followed by 3 CV with buffer, each with a maximum flow rate of 5 ml/min.

Run:

1.) Load the protein solution onto the column using an appropriate super loop (10 ml or 50 ml) and a maximum flow rate of 1 ml/min. Start the automated fractionation system.

2.) Once the protein is loaded, wash the column with lysis buffer using a maximum flow rate of 5 ml/min until the UV absorption has reached a constant value.

3.) Start eluting unspecifically bound, contaminative protein species with a flow rate of 3 ml/min by applying a stepwise gradient from 0 % to 2 % of elution buffer.

4.) Elute the target protein with a flow rate of 3 ml/min by applying a linear gradient from 2 % to 50 % of elution buffer over 20 CV (column volumes).

5.) Analyze obtained peak fractions by SDS-PAGE and pool the fractions containing the target protein.

6.) Reduce the volume of the protein solution via concentration until a maximum volume of 5 ml is reached and apply it to size exclusion chromatography.

All chromatographical purification steps are carried out at 20°C.

Required buffers

Buffer A: Lysis buffer (20 mM phosphate pH 8, 500 mM NaCl, 5 % (v/v) glycerol, 1 mM 2-mercaptoethanol)

Buffer B: Elution buffer (Lysis buffer supplemented with 250 mM imidazole)

Size Exclusion Chromatography

In a second purification step, the target proteins ScaA and RFP-ACEL were separated according to their size (radius of gyration) by employing size exclusion chromatography. Therefore:

Connect a HiLoad Superdex 200 16/600 column (GE Healthcare) to an Äkta purifier or Äkta prime system and wash the column with 1 CV of 20 % EtOH and a maximum flow rate of 1 ml/min.

Pre-equilibrate the column with loading buffer by washing first with 1 CV of water and subsequently with 1 CV of the respective buffer, each with a maximum flow rate of 1 ml/min.

Load the concentrated protein solution with a maximum flow rate of 1 ml/min onto the column by using a 5 ml sampling loop. Start the automated fractionation.

Elute the target protein with a maximum flow rate of 1 ml/min and analyze obtained peak fractions on a SDS gel.

Pool the fractions containing the target protein.

All chromatographic purification steps are carried out at room temperature.

Required buffer:

Buffer A: Loading buffer (20 mM phosphate pH 8, 500 mM NaCl, 5 % glycerol, 1 mM 2-mercaptoethanol)

Concentration of protein solutions

Concentration of protein solutions was realized via centrifugation using 20 ml Vivaspin centrifugal concentrators (Viva Science) with the appropriate molecular weight cutoffs of 50 kDa in case of the scaffolding protein ScaA and 30 kDa in case of RFP-ACEL. In order to concentrate protein solutions:

Wash the concentrator with 20 ml of buffer in order to remove the protectant (glycerol) from the membrane.

Add the protein sample to the concentrator and start centrifugation at 4°C until the desired volume/concentration is reached. The sample volume and the speed is determined by the rotor that is used. If a 25° fixed angle rotor is applied, the maximum starting volume is 14 ml and the speed is restricted to 6000 x g.

Gently mix the upper reservoir prior to each refilling step and prior to transfer.

Check the flow through for leakage by Bradford assay.

Bradford Assay

Bradford Assay

For calculating protein concentrations of an unknown sample the traditional way is to use a standard curve that is generated from known protein standards. Readily available protein standards contain bovine serum albumin (BSA) or bovine gamma globulin (γ-globulin, IgG). The calculated result is an estimation of protein concentration since Bradford protein assays do show significant protein-to-protein variation.

For our Bradford assay we got an already prepared standard solution with a factor of 15.924.

Caution: Store the Bradford solution in the dark, it is light sensitive.

Sample preparation:

Measurement takes place against 20 μL water (blank).

Blank: 20 μL + 1 mL Bradford solution

Samples: 1-20 μL (depending on protein concentration, max. 2 mg/mL) + 19-0 μL water + 1 mL Bradford solution

Prepare photometer cuvettes for technical triplicates of all samples + one blank
Preheat photometer light and set it to 595 nm
Pipet the samples (plus water) and the blank into the cuvettes
Pipet 1 mL Bradford solution on top, carefully homogenize by pipetting up and down
Avoid air bubbles
Incubate the cuvettes in the dark for 5 minutes
Immediately measure the samples at 595 nm

Calculation of protein concentration:

Formula for calculating the protein concentration

SDS Polyacrylamid Gel Electrophoresis

The analytic protein separation according to the apparent molecular weight was carried out by discontinuous SDS polyacrylamid gel electrophoresis according to Laemmli (1970) using mini gel electrophoresis chambers (BioRad, 10x8 cm). For cast and run of the gels do the following:

For the stacking gel use the following components: 0.25 % of the total volume of stacking gel buffer, and acrylamid to a final concentration of 4 %. Add water to the final volume (cf. pipetting scheme). Add 1/133 of the total volume of 10 % ammonium persulfate (APS) and 1/1000 of N,N,N’,N’-tetramethyl-ethylenediamine (TEMED).

For the separation gel mix the appropriate amount of acrylamid (e.g. 10 % for a 10 % SDS gel) with 0.25 % of the final volume of separation gel buffer and fill with water to the final volume. Add 1/133 of the total volume of 10 % APS and 1/1000 of TEMED.

Place the poured gel into the running chamber and fill the upper and lower reservoir with running buffer.

Dilute the protein samples 1:1 with loading buffer and load the gel.

Run the gel with 15mA per gel for 15 min, and then increase to 30mA per Gel until the end.

After electrophoretic separation, place the gels into staining solution and heat it without boiling.

Incubate the gels under slow agitation until protein bands become visible.

Discolor the gels by using fixation solution.

Pipetting scheme.

Compoment (For 2 gels)	Stacking gel (4 % acrylamid)	Separation gel (10 % acrylamid)
Water	2.64 ml	4 ml
Acrylamid	0.4 ml	2 ml
Stacking gel buffer	0.96 ml	---
Separation gel buffer	---	2 ml
Mix
10 % APS	30 µl	60 µl
TEMED	4 µl	6 µl

Required agents and solutions:

40 % Acrylamid/bis-acrylamid (37.5:1)

10 % (w/v) SDS solution

Stacking gel buffer (1.5 M Tris/HCl pH 8.8, 0.4 % (w/v) SDS)

Separation gel buffer (0.5 M Tris/HCl pH 6.5, 0.4 % (w/v) SDS)

2x Laemmli loading buffer (20 mM Tris/HCl pH 6.5, 4 % (w/v) SDS, 10 % (v/v) β-mercaptoethanol, 40 % (v/v) glycerol, 0.002 % (w/v) bromphenol blue)

1x SDS running buffer (25 mM Tris base, 192 mM glycine, 0.1 % (w/v) SDS)

Staining solution (0.005 % (w/v) Coomassie Brilliant Blue G-250, 0.0025 % (w/v) Coomassie Brilliant Blue R-250, 10 % (v/v) ethanol und 5 % (v/v) acetic acid)

Fixation solution (10 % (v/v) acetic acid)

Western Blot

10 x TBS Buffer (store at RT)

Tris HCL (MW: 121,14 g/mol)	6.057g
NaCl (MW: 58.44 g/mol)	40.91g
H₂O dest.	ad. 500 ml

adjust to pH 7.4

1 x Transfer Buffer (store at RT)

Tris	3.029 g
Glycin	14,41g
Methanol	200ml
H₂O bidest.	ad. 1000ml

check pH: 8.1-8.4

If the pH is not correct, the Buffer has to be remade. Do not adjust.

10 x TBS-Tween Buffer (store at RT)

Tris-HCL (MW: 121.14 g/mol)	6.057g
NaCl (MW: 58.44 g/mol)	40.91g
Tween20 (Endkonz. 0,1%)	0.5ml
H₂O bidest.	ad. 500ml

adjust to pH 7.4

Blocking Solution

Skim Milk	2,5g
1 x TBS	50ml

Dissolve for 15-30 min at RE. Store 400µl at 4°C for a later step.

Phosphatase Buffer (store at RT)

Tris-HCL (MW: 121.14 g/mol)	6.057g
NaCl (MW: 58.44 g/mol)	2.922 g
MgCl₂x 6 H₂O (MW: 203.3 g/mol)	0.51 g
H₂O bidest.	ad. 500ml

adjust to pH 9.5

Antibody: Anti V5-AP Antibody (Invitrogen, store at 4°C)

NBT: Promega, 50 mg/ml, store at -20°C

BCIP: Promega, 50 mg/ml, store at -20°C

1.) Run an SDS Gel and use Protein Ladder compatible with Western Blots.

2.) Use Perfect Blue Semi-Dry Electro blotter from Peqlab and assemble apparatus in a tip box with a little transfer buffer (sandwich should be moist not wet):

Base of blotter = Kathode (+) bottom

3x Whatman paper (moist) size of SDS page

Blotting membrane (Hybond EHL, 0,45µm, moist, no bubbles, SDS page sized)

SDS Gel (no bubbles! Proteins have a neg. charge and go towards the Kathode)

3x Whatman paper (moist, gel sized)

Lid = Anode (-) top

After assembly of the sandwich the lid is screwed on lightly with 3 screws. Connect Blotter to an adequate power supply, which can work at a constant 10V. Blot at 200mA per Gel and constant 10V for 1 hour.

3.) Wash the membrane 3x 5 min with 1x TBS Buffer on a rocker

4.) Block membrane in 50ml 1 x TBS Buffer with 5% skim milk for one hour or overnight on a rocker.

5.) Wash 3x 15min 1xTBS-Tween on a rocker

6.) Prepare Antibody: 14ml 1xTBS-Tween + 200µl 1x TBS Puffer/5% Skimmilk + 7µl Antibody

7.) Incubate with antibody for 2 hours on a rocker

8.) Wash 2x shortly in 1x TBS-Tween Buffer on a rocker

9.) 1x 15min 1x TBS-Tween Buffer on the rocker

10.) 2x 5min 1x TBS-Tween Buffer on the rocker

11.) Wash 2x 10 min 1x TBS Buffer on a rocker

12.) Wash 2x shortly in 1x Phosphatse buffer

13.) 10ml 1x Phosphatase buffer + 66µl NBT + 33µl BCIP

- stain in the dark until bands become visible

- stop the reaction by washing with H2O

- dry western blot in Whatman Paper

14.) Scan the membrane

Activity Screens & Tests

Esterase activity test

Materials:

Substrate- 1mM 4-nitrophenyl butyrate prepared in Na-Phosphate buffer (pH 8.0)

Protein sample

Procedure:

- Add 2 µl of the protein sample to 2ml of the substrate and incubate for 5 minutes

- The colour change from white/transparent to yellow is observed which indicates the presence of the enzyme

Phosphatase activity test

Materials:

Freshly prepared AAM Solution (Acetone, 5N H₂SO₄, 10 mM Ammonium molybdate, 2:1:1 v/v)
50 mM Sodium acetate buffer, pH 5.0
100 mM Pyrophosphate
1 M Citric acid
Protein sample

Procedure:

Set a heating block to 37°C or 40°C
Place 2 mL reaction tubes for each sample (technical triplicates) plus one blank in the heating block
Pipet 250 µL of 50mM Sodium acetate buffer in all reaction tubes
Add 40 µL of protein sample
Add 10 µL of 100 mM Pyrophosphate to the tubes
Mix the tubes by inverting
Incubate on the heating block for 30 minutes
Add 1.5 mL of AAM solution and homogenize by inverting the tubes
Add 100 µL 1 M Citric acid
If phosphatase is present, the colour will change from white/transparent to yellow
Measure the colour strength in a photometer at 355 nm

CAUTION: Make sure that the buffer you used for protein extraction does not contain any phosphate components. Otherwise the test will be false positive!

Cellulase activity screening

Streak Competent Top10 E. coli cells or Competent BL21 cells transformed with appropriate vector containing cellulase construct onto agar plates containing cellulose substrate.
Incubate plates at 37^oC for minimum 3-4 days (timing can be extended depending on bacterial strain).
After 3-4 days look for plates having clear zone of activity around cellulose substrate.

Enzymatic Activity Test for Cellulase

Solutions:

Buffer:

Tris (MW: 121.14 g/mol) 50 mM

dH₂O ad 1 l

pH 7

Substrate solution:

Carboxymethil cellulose 1 % (w / v)

ddH₂O ad 1 l

DNSA reagent solution:

Dinitrosalycylic acid 10 g

Phenol 2 ml

K Na Tartrate 200 g

NaOH 10 g

Na₂SO₃ 0.5 g

dH₂O ad 1 l

Store at 4°C, protected from light

Procedure:

250 µl substrate solution

100 µl Tris-Buffer

x µl enzyme solution

ad 500 µl ddH₂O

Incubate setup as described above at 37°C for 20 min.

Add 750 µl DNSA. Heat the setup at 96°C for 15 min.

Put mixture on ice, centrifuge shortly at 4°C, 13000 x g.

Measure OD₅₇₅ against same setup without enzyme as a blank.

Restriction Controls

Aan I (Psi I ) - thermo fisher scientific - restriction control protocol

- Add the following components

Purified Plasmid	1 µg
10X Buffer Tango	1 µl
Ana I (Psi I) (10 U/L)	0.5 µl
Nuclease free H₂O	Add to 10 µl

- Incubate at 37 ^oC for 2 hours

- For inactivation incubation at 65°C for 20 min.

Double digestion restriction control

Double digestion restriction control

Sac I and Pvu II - thermo fisher scientific - restriction control protocol

Add the following components

Purified Plasmid	800 ng
Sac I (2x)	2 µl
Pvu II (1x)	1 µl
10x Tango buffer	2 µl
Nuclease free H₂O	Add to 20 µl

For 10 µl reaction add 1 µl of 10x Tango buffer, for 20 µl reaction add 2 µl of 10x Tango buffer and vice versa.
Incubate at 37 ^oC for 2 hours.
For inactivation incubation at 80°C for 5 min.
Check the products on 0.8% agarose gel.

Restriction control using fast and slow digestion enzymes

Restriction control using fast digestion enzymes

Sac I and HindIII - thermo fisher scientific - restriction control protocol

Add the following components

Purified Plasmid	500-1,000 ng
Sac I	1 µl
Hind III	1 µl
Nuclease free H₂O	Add to 10 µl

Incubate at 37 ^oC for 30 min.
For inactivation incubation at 65°C for 5 min.

PST I - thermo fisher scientific - restriction control protocol

Add the following components

Purified Plasmid	500-1,000 ng
FD buffer	1 µl
PST I	1 µl
Nuclease free H₂O	Add to 10 µl

Incubate at 37 ^oC for 30 min.
Products were checked on 0.8% agarose gel.

Restriction control using slow digestion enzymes

Bsm I - fermentas - restriction control protocol

Add the following components

Purified Plasmid	500 ng
Red buffer	1 µl
Bsm I	1 µl
Nuclease free H₂O	Add to 8 µl

Incubate at 37 ^oC for 3 hours.
Products were checked on 0.8% agarose gel.

Scafoldin Restriction control

Scaffoldin Restriction Control using the restriction enzyme BsmI

Set up the reaction as follows,

Components	Quantity
Nuclease free Water	15 µl
Red Buffer 10X	2 µl
DNA	1,000 ng (2 µl)
BsmI	1 µl
	20 µl

Incubate the mixture for 2 hours at 37ᵒC.

Perform the heat inactivation step for the reaction mixture for 10 min at 65ᵒC.

Esterase Restriction Control

Esterase Restriction Control

Nuclease Free Water	15 µl
R Buffer 10X	2 µl
DNA (up to 1µg)	2 µl
XhoI (10U/µl)	1 µl
PstI (10U/µl)	1 µl

Incubate 20 min at 37˚C and inactivate 5 min at 80˚C.

Phosphatase Restriction Control

Phosphatase Restriction Control

Nuclease Free Water	14µl
Fast digestion Buffer 10X	2µl
DNA ( up to 1µg)	2µl
SacI (10U/µl)	1µl
KpnI(10U/µl)	1µl

Incubate 2 hours at 37˚C and inactivate 20min at 80˚C.

PCR Preparation Methods

Colony PCR

Colony PCR

- Pick a colony with a tip and re suspend it in 5ul LB

- Prepare the PCR mix as follows:

Water	12 ul
Taq Buffer	2 ul
MgCl	2 ul
dNTPs	0.5 µl
Primer Forward	1 ul
Primer Reverse	1 ul
Taq Polymerase	1.5 µl

- Program:

Initial denaturalization: 98˚C, 5 min

Denaturalization: 96˚C, 45 s

Annealing: 70˚C, 30 s

Elongation: 72˚C, 25 s

Phusion PCR

This protocol describes PCR procedure using Phusion High-Fidelity DNA Polymerase. (Thermo Fisher Scientific).

• Note: the annealing conditions depend on the applied DNA polymerases (such as Taq DNA polymerases).

•Use 15–30 s/kb for extension. Do not exceed 1 min/kb.

•Phusion DNA Polymerases produce blunt end DNA products.

•All components and reaction mix are placed on ice.

- add the following components, mix and spin down.

Component	20 µL rxn	50 µL rxn	Final conc.
H₂O	add to 20 µL	add to 50 µL
5X Phusion HF Buffer	4 µL	10 µL	1X
10 mM dNTPs	0.4 µL	1 µL	200 µM each
Forward primer	X µL	X µL	0.5 µM
Reverse primer	X µL	X µL	0.5 µM
Template DNA	15 -20 ng	30 - 50 ng
(DMSO, optional)*	(0.6 µL)	(1.5 µL)	3%
Phusion DNA Polymerase	0.2 µL	0.5 µL	0.02 U/µL

* Addition of DMSO is recommended for GC-rich amplicons. DMSO is not recommended for amplicons with very low GC % or amplicons that are > 20 kb.

- adjust the thermocycle to the following isntructions and start the PCR.

Cycle step	Tempreature ^oC	Time	Cycles
Initial Denaturation	98	30 s	1
Denaturation	98	5–10 s	30 - 35
Annealing	*	10–30 s
Extension	72	15–30 s/kb
Final extension	72	5-10 min	1

* The optimal annealing temperature for Phusion DNA Polymerase may differ significantly from that of Taq-based polymerases. Always use the Tm calculator and instructions on our website (www.thermoscientific.com/pcrwebtools) to determine the Tm values of primers and optimal annealing temperature. The Phusion DNA Polymerase has the ability to stabilize primer-template hybridization. As a basic rule, for primers > 20 nt, anneal for 10–30 seconds at a Tm +3°C of the lower Tm primer. For primers ≤ 20 nt, use an annealing temperature equal to the Tm of the lower Tm primer.

- for Templates > 2.5 kb and primers with low stability apply the following program

Cycle step	Tempreature ^oC	Time	Cycles
Initial Denaturation	98	30 s	1
Denaturation	98	10 s	30 - 35
Annealing	*	15 s
Extension	72	1 min 30 s
Final extension	72	10.5 min	1

- check the PCR product on 0.8% agarose gel and store at - 20 celsius degrees.

Sequencing

Protocol for Sanger sequencing

Sequencing reaction setup

Template	DNA amount
PCR products	10 ng/100 bp (if larger 1.5 kb 150 ng)
Plasmids	300 ng
Forward primer (5pmol/ µl )	1 µl
Reverse primer (5pmol/ µl )	1 µl
Nuclease free H₂O	ad. 5 µl
Total volume	5 µl

Forward and reverse primers should be added in 2 individual sample tubes!

Overnight Sanger Sequencing

Sanger sequencing reaction setup for overnight

Components	Volume
Purified Plasmid	800 ng
Forward primer (1:10)	3 µl
Reverse primer (1:10)	3 µl
Nuclease free H₂O	ad. 15 µl
Total volume	15 µl

Forward and reverse primers should be added in 2 individual sample tubes!

Fluorescence Microscopy

RFP microscopy

RFP microscopy

To check if the transformed E.coli TOP10 show red fluorescence, the culture was examined by fluorescence microscopy. The RFP DsRed filter was used (excitation at 536 nm, emission at 582 nm). To prevent the cells from floating around they are fixed in 0.8%.

Preparation of slides

Prepare 0.8% agarose with water and boil it up.
Pipet 500 μL onto a slide and press another one on top. Let the agarose cure between both slides.
Carefully remove the upper slide and put the sample name in one corner the one with the agarose.
Dilute the desired cell cultures 1:10 up to 1:50 (depends on thickness) and remember to prepare also a positive (if available) and negative control.
Pipet 10-20 μL of the diluted culture on the agarose and put the cover slip on top.
Perform fluorescence microscopy with the right filter.
If successful, take pictures of the red fluorescing E. coli.
Note: Agarose has a slight self-fluorescence.

@@ Line 1: / Line 1: @@
 {{Goettingen}}
-<html>
-</html>
-[[File:Workflow.jpeg|600px|thumb|center|]]
 <html>
@@ Line 40: / Line 37: @@
 }
-#menu1, #menu2, #menu3, #menu4, #menu5, #menu6, #menu7, #menu8, #menu9, #menu10, #menu11, #menu12, #menu13, #menu14, #menu15, #menu16, #menu17, #menu18, #menu19, #menu20, #menu21, #menu22, #menu23, #menu24, #menu25, #menu26, #menu27, #menu28, #menu29, #menu30{
+#menu1, #menu2, #menu3, #menu4, #menu5, #menu6, #menu7, #menu8, #menu9, #menu10, #menu11, #menu12, #menu13, #menu14, #menu15, #menu16, #menu17, #menu18, #menu19, #menu20, #menu21, #menu22, #menu23, #menu24, #menu25, #menu26, #menu27, #menu28, #menu29, #menu30, #menu31, #menu32, #menu33, #menu34, #menu35, #menu36, #menu37, #menu38, #menu39, #menu40, #menu41{
      display:none;
      width:90%;
@@ Line 58: / Line 55: @@
 </style>
 <!-- End of CSS -->
-<h2> Media </h2>
+<h2> Media/Buffer </h2>
 <a href="" onClick=" $('#menu1').slideToggle(300, function callback() {  }); return false;"><h1 style="color:white;">LB Medium</h1></a>
 <div id="menu1">
@@ Line 94: / Line 91: @@
              </td>
              <td valign="top" width="150">
-                 <p>ad. 1000mL</p>
+                 <p>ad. 1000 mL</p>
              </td>
          </tr>
@@ Line 103: / Line 100: @@
      </ul>
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Autoclave at 121 <sup>o</sup>C for 20 min.</p>
-     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; The preferred antibiotic is added with the proper concentration (e.g Ampicilin is added to a final concentration of 100 &micro;g/ml)</p>
+     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; The preferred antibiotic is added from a concentrated stock solution to an appropriate concentration (e.g Ampicilin is added to a final concentration of 100 &micro;g/ml).</p>
      <ul>
          <li>To the liquid medium antibiotic is added upon usage.</li>
@@ Line 121: / Line 118: @@
              <td valign="top" width="307">
                  <p>
-                     Oxoid Yeast extract
+                     Yeast extract
                  </p>
              </td>
              <td valign="top" width="97">
                  <p>
 g
                  </p>
              </td>
@@ Line 133: / Line 130: @@
              <td valign="top" width="307">
                  <p>
-                     KH<sub>2</sub>PO<sub>4</sub> (MW: 136,09)
+                     KH<sub>2</sub>PO<sub>4</sub> (MW: 136.09)
                  </p>
              </td>
              <td valign="top" width="97">
                  <p>
-,0g
+.0 g
                  </p>
              </td>
@@ Line 150: / Line 147: @@
              <td valign="top" width="97">
                  <p>
-,14g
+.14 g
                  </p>
              </td>
@@ Line 162: / Line 159: @@
              <td valign="top" width="97">
                  <p>
-                     ad. 1000mL
+                     ad. 1000 mL
                  </p>
              </td>
@@ Line 169: / Line 166: @@
 </table>
 <p>
-     pH 6,8 with NaOH (ca. 10mL 1M NaOH)
+     pH 6.8 with NaOH (ca. 10mL 1M NaOH)
 </p>
 <p>
@@ Line 184: / Line 181: @@
              <td valign="top" width="97">
                  <p>
 mL
                  </p>
              </td>
@@ Line 196: / Line 193: @@
              <td valign="top" width="97">
                  <p>
-,5mL
+.5 mL
                  </p>
              </td>
@@ Line 202: / Line 199: @@
      </tbody>
 </table>
+</div>
+<a href="" onClick=" $('#menu37').slideToggle(300, function callback() {  }); return false;"><h1 style="color:white;"> Media and Culture Methods for Dockerin Organisms of Origin</h1></a>
+<div id="menu37">
+<p>
+    <strong>Pseudobacteroides cellulosolvens</strong>
+</p>
+<p>
+   <a href="https://www.dsmz.de/microorganisms/medium/pdf/DSMZ_Medium315.pdf">DSMZ Medium 315</a>
+</p>
+<p>
+    <strong>Clostridium cellulolyticum</strong>
+</p>
+<p>
+   <a href="https://www.dsmz.de/microorganisms/medium/pdf/DSMZ_Medium520.pdf"> DSMZ Medium 520</a>
+</p>
+<p>
+    <strong>Clostridium thermocellum</strong>
+</p>
+<p>
+   <a href="https://www.dsmz.de/microorganisms/medium/pdf/DSMZ_Medium122.pdf">DSMZ Medium 122</a>
+</p>
+<p>
+    <strong>Acetivibrio cellulolyticus</strong>
+</p>
+<p>
+   <a href="https://www.dsmz.de/microorganisms/medium/pdf/DSMZ_Medium165.pdf">DSMZ Medium 165</a>
+</p>
+<p>
+    <a href="http://www.dsmz.de/microorganisms/medium/pdf/DSMZ_Medium141.pdf">DSMZ Medium 141</a>
+</p>
 </div>
@@ Line 211: / Line 239: @@
 <p>&nbsp;</p>
 <p><span style="text-decoration: underline;">A: Stock reagents</span></p>
-<p>1M IPTG (4,76 g in 20ml Millipore-H2O) filter with blue 0,22 um sterile filter and freeze at -20˚C</p>
+<p>1M IPTG (4.76 g in 20ml Millipore-H2O) filter with blue 0.22 µm sterile filter and freeze at -20˚C</p>
-<p>50mg/ml Kanamycin in Millipore H2O, filter with blue 0,22 um sterile filter and freeze at -20˚C</p>
+<p>50mg/ml Kanamycin in Millipore H2O, filter with blue 0.22 µm sterile filter and freeze at -20˚C</p>
-<p>100mg/ml Ampicillin in 50% ethanol, filter with blue 0,22 um sterile filter and freeze at -20˚C</p>
+<p>100mg/ml Ampicillin in 50% ethanol, filter with blue 0.22 µm sterile filter and freeze at -20˚C</p>
-<p>25mg/ml BCIP (in DMF) filter with blue 0,22 um sterile filter and keep in a falcon tube wrapped with aluminum foil at 4˚C. BCIP: Biomol Nr. 2291 (MG 433,64)</p>
+<p>25mg/ml BCIP (in DMF) filter with blue 0.22 µm sterile filter and keep in a falcon tube wrapped with aluminum foil at 4˚C. BCIP: Biomol Nr. 2291 (MG 433.64)</p>
 <p>Glycerol (99%), autoclaved and kept at room temperature</p>
 <p>&nbsp;</p>
 <p><span style="text-decoration: underline;">B: Sperber medium</span></p>
 <p>1g Yeast extract</p>
-<p>3,5 ml 50% w/w Phytic acid</p>
+<p>3.5 ml 50% w/w Phytic acid</p>
-<p>0,2g CaCl2</p>
+<p>0.2 g CaCl2</p>
-<p>0,5g MgSO4</p>
+<p>0.5 g MgSO4</p>
-<p>Adjust the pH to 7,2 with NaOH</p>
+<p>Adjust the pH to 7.2 with NaOH</p>
-<p>Ad 2L of Millipore H2O</p>
+<p>Ad 2 L of Millipore H2O</p>
-<p>32g agar</p>
+<p>32 g agar</p>
 <p>Autoclave</p>
 <p>&nbsp;</p>
@@ Line 230: / Line 258: @@
 <p>&nbsp;</p>
 <p>For 2 L medium:</p>
-<p>2ml BCIP</p>
+<p>2 ml BCIP</p>
-<p>2ml 1M IPTG</p>
+<p>2 ml 1M IPTG</p>
-<p>2ml Ampicllin or Kanamycin</p>
+<p>2 ml Ampicllin or Kanamycin</p>
-<p>40mL Glycerol</p>
+<p>40 mL Glycerol</p>
 <p>The media is now ready for plating</p>
 <p><br /> <strong>Result</strong>: On Sperber medium phosphatase-recombinant colonies should develop a distinct color blue after 2 days.</p>
@@ Line 243: / Line 271: @@
 <p style="text-align: center;"><span style="font-size: x-large; color: #888888;"><strong><span lang="EN-GB"></span></strong></span></p>
 <p><span lang="EN-GB">&nbsp;</span></p>
-<p><span lang="EN-GB">To 500ml of LB Media add 7,5g of Agar and 5ml of Tributyrin and homogenize with a mixer.</span></p>
+<p><span lang="EN-GB">To 500 ml of LB Media add 7.5 g of Agar and 5 ml of Tributyrin and homogenize with a mixer.</span></p>
 <p><span lang="EN-GB">This culture medium must be directly sterilized by autoclaving at 121˚C for 20 min.</span></p>
 <p><span lang="EN-GB">If you wait too long it will be inhomogeneous again!</span></p>
-<p><span lang="EN-GB">When the medium cools down enough, the antibiotic can be added.</span></p>
+<p><span lang="EN-GB">When the medium cools down to 50°C, the antibiotic can be added.</span></p>
 <p><span lang="EN-GB">&nbsp;</span></p>
 <p><strong><span lang="EN-GB">Result:</span></strong><span lang="EN-GB"> Halo formation is visible around the positive clones.</span></p>
@@ Line 313: / Line 341: @@
      <p>The stock solution will be stored at +4 &deg;C.</p>
      <p><strong>C: Prepare the agar plates</strong></p>
-     <p>When the medium cools down to around 60&deg;C, put the bottle containing LB-agar base on a magnetic mixer. At the same time, disperse the substrate by flip the falcon tube several times. Then, pour the substrate into the LB-agar base gently until the substrate suspend evenly in the agar medium (For how much substrate should be poured, ask the supervisor). Other reagents like antibiotic can also be added. Ca. 3-5 ml substrate per Liter medium.</p>
+     <p>When the medium cools down to around 60 &deg;C, put the bottle containing LB-agar base on a magnetic mixer. At the same time, disperse the substrate by flip the falcon tube several times. Then, pour the substrate into the LB-agar base gently until the substrate suspend evenly in the agar medium (For how much substrate should be poured, ask the supervisor). Other reagents like antibiotic can also be added. Ca. 3-5 ml substrate per Liter medium.</p>
      <p><strong>D: Preparation of agar plates contacting cellulose substrate</strong></p>
      <p>After dispersing substrate and adding antibiotic to LB-agar , pour the medium quickly with continuous stirring onto the plates and make sure to make a thin layer of medium. Let the plates to dry and store them at 4 &deg;C.</p>
@@ Line 325: / Line 353: @@
      <p>&nbsp;</p>
 </div>
+<a href="" onClick=" $('#menu33').slideToggle(300, function callback() {  }); return false;"><h1 style="color:white;">1x TAE Buffer</h1></a>
+<div id="menu33">
+<p>1 x TAE Buffer</p>
+<table border="1" cellspacing="0" cellpadding="0">
+    <tbody>
+        <tr>
+            <td valign="top" width="307">
+                <p>Tris</p>
+            </td>
+            <td valign="top" width="307">
+                <p>24.22 g</p>
+            </td>
+        </tr>
+        <tr>
+            <td valign="top" width="307">
+                <p>Acetic acid (100%)</p>
+            </td>
+            <td valign="top" width="307">
+                <p>5.74 ml</p>
+            </td>
+        </tr>
+        <tr>
+            <td valign="top" width="307">
+                <p>EDTA (0.5M, pH 8.0)</p>
+            </td>
+            <td valign="top" width="307">
+                <p>10 ml</p>
+            </td>
+        </tr>
+        <tr>
+            <td valign="top" width="307">
+                <p>H<sub>2</sub>O dest.</p>
+            </td>
+            <td valign="top" width="307">
+                <p>ad. 5 L</p>
+            </td>
+        </tr>
+    </tbody>
+</table>
+<p>&nbsp;</p>
+</div>
 <h2> Cloning Methods </h2>
 <a href="" onClick=" $('#menu6').slideToggle(300, function callback() {  }); return false;"><h1>PCR product purification using QIAquick&reg; PCR Purification Kit (QIAGEN)</h1></a>
@@ Line 331: / Line 403: @@
      <ul>
          <li>Add ethanol (96&ndash;100%) to Buffer PE before use.</li>
-         <li>All centrifugation steps are carried out at 17,900 x g (13,000 rpm) in a conventional table-top microcentrifuge at room temperature.</li>
+         <li>All centrifugation steps are carried out at 17900 g in a conventional table-top microcentrifuge at room temperature.</li>
      </ul>
      <p>&nbsp;</p>
@@ Line 347: / Line 419: @@
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Fractionate DNA fragments by running a agarose gel (Do not stain the gel with Ethidium bromide or expose the DNA to UV for too long).</p>
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Add equal volume of Binding Buffer to the gel slice and incubate at 65ᵒC for 8 min. Vortex or mix every 2 to 3 min until the agarose dissolves completely. (0.2 g of gel equivalent to 0.2 ml)</p>
-     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Pour the mixture into PerfectBind DNA column (which is placed in a 2 ml collection tube) and centrifuge for 1 min at 10,000 x g.(max. 750 &micro;l) Discard the flow-through and place the PerfectBind DNA column in the same tube. Repeat the steps if required.</p>
+     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Pour the mixture into PerfectBind DNA column (which is placed in a 2 ml collection tube) and centrifuge for 1 min at 10000 x g.(max. 750 &micro;l) Discard the flow-through and place the PerfectBind DNA column in the same tube. Repeat the steps if required.</p>
-     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Add 300 &micro;l of binding Buffer to the PerfectBind DNA column for the washing the contaminants and centrifuge for 1 min at 10,000 x g. Discard the flow-through and place the column in the same tube</p>
+     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Add 300 &micro;l of binding Buffer to the PerfectBind DNA column for the washing the contaminants and centrifuge for 1 min at 10000 x g. Discard the flow-through and place the column in the same tube</p>
-     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Add 750 &micro;l of CG Wash Buffer to the PerfectBind DNA column for the wash, incubate for 2 to 3 min and centrifuge for 1 min at 10,000 x g. Discard the flow-through and place the column in the same tube. Repeat this step once more.</p>
+     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Add 750 &micro;l of CG Wash Buffer to the PerfectBind DNA column for the wash, incubate for 2 to 3 min and centrifuge for 1 min at 10000 x g. Discard the flow-through and place the column in the same tube. Repeat this step once more.</p>
-     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Centrifuge the PerfectBind DNA column once more in the 2 ml collection tube for 1 min at 10,000 x g to remove the residual wash buffer.</p>
+     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Centrifuge the PerfectBind DNA column once more in the 2 ml collection tube for 1 min at 10000 x g to remove the residual wash buffer.</p>
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Place the PerfectBind DNA column in a clean 1.5 ml eppendorf tube.</p>
-     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Add 50 &micro;l of pre-warmed sterile water to the PerfectBind DNA column and incubate for 2 to 3 min (normally in a 2 step process of 30 &micro;l in first elution step and 20 &micro;l in second elution step) and centrifuge at 5,000 x g for 1 min.</p>
+     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Add 50 &micro;l of pre-warmed sterile water to the PerfectBind DNA column and incubate for 2 to 3 min (normally in a 2 step process of 30 &micro;l in first elution step and 20 &micro;l in second elution step) and centrifuge at 5000 x g for 1 min.</p>
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Store the purified DNA at -20ᵒC.</p>
      <p>&nbsp;</p>
      <p></p>
 </div>
-<a href="" onClick=" $('#menu4').slideToggle(300, function callback() {  }); return false;"><h1>Blunt End Ligation in pJET1.2 vector &ndash;Clone JET PCR Cloning Kit&ndash;Thermo Scientific</h1></a>
+<a href="" onClick=" $('#menu4').slideToggle(300, function callback() {  }); return false;"><h1>Blunt End Ligation in pJET1.2 vector &ndash;Clone JET PCR Cloning Kit&ndash; (Thermo Scientific)</h1></a>
 <div id="menu4">
      <p>&nbsp;</p>
@@ Line 376: / Line 448: @@
              </td>
              <td valign="top" width="246">
-                 <p>10&micro;l</p>
+                 <p>10 &micro;l</p>
              </td>
          </tr>
@@ Line 384: / Line 456: @@
              </td>
              <td valign="top" width="246">
-                 <p>125ng</p>
+                 <p>125 ng</p>
              </td>
          </tr>
@@ Line 392: / Line 464: @@
              </td>
              <td valign="top" width="246">
-                 <p>50ng (1&micro;l)</p>
+                 <p>50 ng (1&micro;l)</p>
              </td>
          </tr>
@@ Line 400: / Line 472: @@
              </td>
              <td valign="top" width="246">
-                 <p>1&micro;l</p>
+                 <p>1 &micro;l</p>
              </td>
          </tr>
@@ Line 408: / Line 480: @@
              </td>
              <td valign="top" width="246">
-                 <p>x&micro;l</p>
+                 <p>x &micro;l</p>
              </td>
          </tr>
@@ Line 416: / Line 488: @@
              </td>
              <td valign="top" width="246">
-                 <p>20&micro;l</p>
+                 <p>20 &micro;l</p>
              </td>
          </tr>
@@ Line 425: / Line 497: @@
      <p>Cloning principle:</p>
      <ul>
-         <li>pJET1.2 is a linearized cloning vector which accepts inserts from 6 bp to 10 kb. Since the 5&rsquo;-ends of the vector contain phosporyl groups, therefore phosphorylation of the PCR products is not required.</li>
+         <li>pJET1.2 is a linearized cloning vector designed for inserts from 6 bp to 10 kb. The 5&rsquo;-ends of the vector contain phosporyl groups, therefore phosphorylation of the PCR products is indicated.</li>
      </ul>
      <ul>
@@ Line 431: / Line 503: @@
      </ul>
      <ul>
-         <li>Optimal PCR product quantity for ligation reaction is to be calculated from the Kit protocol, For the length of 2500 bp of PCR product, to have 0.15 pmol ends of the PCR product in the ligation reaction 125 ng of the PCR product should be used.</li>
+         <li>Optimal PCR product quantity for ligation reaction is to be calculated from the Kit protocol, For the length of 2.5 kb of PCR product, to have 0.15 pmol ends of the PCR product in the ligation reaction 125 ng of the PCR product should be used.</li>
      </ul>
      <ul>
@@ Line 437: / Line 509: @@
      </ul>
      </div>
-     <a href="" onClick=" $('#menu5').slideToggle(300, function callback() {  }); return false;"><h1>TOPO&reg; Cloning protocol usingChampion&trade; pET Directional TOPO&reg; Expression Kits. Thermo Fisher Scientific</h1></a>
+<a href="" onClick=" $('#menu32').slideToggle(300, function callback() {  }); return false;"><h1>Sticky End T4 Ligation (Thermo Scientific)</h1></a>
+<div id="menu32">
+<p><strong>T4 Ligation - Thermo Fisher Scientific - sticky end ligation</strong></p>
+<p>1. Prepare the following reaction mixture:</p>
+<table border="1" cellspacing="0" cellpadding="0">
+    <tbody>
+        <tr>
+            <td valign="top" width="184">
+                <p>Linear vector DNA</p>
+            </td>
+            <td valign="top" width="104">
+                <p align="center">20 ng</p>
+            </td>
+        </tr>
+        <tr>
+            <td valign="top" width="184">
+                <p>Insert DNA</p>
+            </td>
+            <td valign="top" width="104">
+                <p align="center">80 ng</p>
+            </td>
+        </tr>
+        <tr>
+            <td valign="top" width="184">
+                <p>10x T4 DNA Ligase buffer</p>
+            </td>
+            <td valign="top" width="104">
+                <p align="center">2 &micro;l</p>
+            </td>
+        </tr>
+        <tr>
+            <td valign="top" width="184">
+                <p>Thermo Scientific T4 DNA Ligase (Cat #EL0016)</p>
+            </td>
+            <td valign="top" width="104">
+                <p align="center">1 U</p>
+            </td>
+        </tr>
+        <tr>
+            <td valign="top" width="184">
+                <p>Nuclease free H<sub>2</sub>O</p>
+            </td>
+            <td valign="top" width="104">
+                <p align="center">Add to 20 &micro;l</p>
+            </td>
+        </tr>
+    </tbody>
+</table>
+<p>2. Incubate 1 hour at RT</p>
+<p>3. Heat inactivation of T4 DNA Ligase at 65 &deg;C for 10 minutes or at 70 &deg;C for 5 min</p>
+</div>
+     <a href="" onClick=" $('#menu5').slideToggle(300, function callback() {  }); return false;"><h1>TOPO&reg; Cloning protocol usingChampion&trade; pET Directional TOPO&reg; Expression Kits (Thermo Fisher Scientific)</h1></a>
 <div id="menu5">
      <ul>
-         <li>You will perform TOPO&reg; Cloning in a reaction buffer containing salt. Note that the amount of salt added to the TOPO&reg; Cloning reaction varies depending on whether you plan to transform chemically competent cells or electrocompetent cells.</li>
+         <li>You will perform TOPO&reg; Cloning in a reaction buffer containing salt. Note: the amount of salt added to the TOPO&reg; Cloning reaction has to be adapted to the planned transformation protocol (chemically competent cells or electrocompetent cells).</li>
      </ul>
      <p><strong>&nbsp;</strong>-&nbsp;&nbsp;&nbsp; Set up the TOPO&reg; Cloning reaction depending on the transformation method.</p>
@@ Line 492: / Line 617: @@
          <tr>
              <td valign="top" width="174">
-                 <p>Sterile Water</p>
+                 <p>Sterile water</p>
              </td>
              <td valign="top" width="212">
@@ Line 561: / Line 686: @@
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Transfer the culture without any air bubbles into pre-cooled electroporation cuvettes (40 &micro;l maximum) and incubate on ice for 10 minutes.</p>
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Electroporate using the electroporator with 1.25 mV, 5 decharge time.</p>
-     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Immediately after electroporation, transfer 300 &micro;l room temperature LB medium on top of the cells&nbsp; and transfer it into an 1.5ml fresh E-cup</p>
+     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Immediately after electroporation, transfer 300 &micro;l room temperature LB medium on top of the cells&nbsp; and transfer it into an 1.5 ml fresh E-cup</p>
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Incubate the culture for 1 hour at 37&deg;C and 150 rpm</p>
      <p><sup>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </sup>Spread a 100 &micro;l from the dilution series (10<sup>-3</sup> to 10<sup>-6</sup>) on a pre-warmed LB plate containing ampicillin</p>
@@ Line 582: / Line 707: @@
      <p>- Inoculate the medium with the desired <em>E.coli</em> strain and incubate overnight at 37 <sup>o</sup>C with agitation (150 rpm).</p>
-     <p>- Pellet the overnight culture by centrifugation at 8000 rpm (6800xg) for 3 min at room temperature.</p>
+     <p>- Pellet the overnight culture by centrifugation at 8,000 rpm (6,800xg) for 3 min at room temperature.</p>
      <p>- Resuspend pelleted bacterial cells in 250 &mu;l Buffer P1 and transfer it to a microcentrifuge tube.</p>
@@ Line 590: / Line 715: @@
      <p>- Add 350 &mu;l Buffer N3 and mix immediately and thoroughly by inverting the tube 4&ndash;6 times.</p>
-     <p>- Centrifuge for 10 min at 13,000 rpm (~17,900 x g) in a table-top microcentrifuge.</p>
+     <p>- Centrifuge for 10 min at 17,900 x g in a table-top microcentrifuge.</p>
      <p>- Apply the supernatant to the QIAprep spin column by decanting. Centrifuge 60 s. Discard the flow-through.</p>
@@ Line 622: / Line 747: @@
      </p>
      <p>
-         Centrifuge the culture at 10000 x g for 2 min to obtain the pellet and repeat the process until the culture is completely centrifuged. Store the pellet of
+         Centrifuge the culture at 10,000 x g for 2 min to obtain the pellet and repeat the process until the culture is completely centrifuged. Store the pellet of
 ml of the culture at -20°C for future use.
      </p>
@@ Line 634: / Line 759: @@
      <p>
          Add 350 µl of Solution III to the cleared lysate and gently mix by inverting the tubes 6 -10 times until a flocculent white precipitate is formed.
-         Centrifuge at 10000 x g for 10 min at room temperature.
+         Centrifuge at 10,000 x g for 10 min at room temperature.
      </p>
      <p>
          Transfer the clear supernatant to a fresh PerfectBind DNA Column in a 2 ml Collection Tube. Centrifuge the Column with the Collection Tube for 1 min at
-x g at room temperature. Discard the flow-through liquid.
+,000 x g at room temperature. Discard the flow-through liquid.
      </p>
      <p>
-         Add 500 µl of PW Plasmid buffer to the PerfectBind DNA Column in the Collection Tube and centrifuge for 1 min at 10000 x g. Discard the flow-through.
+         Add 500 µl of PW Plasmid buffer to the PerfectBind DNA Column in the Collection Tube and centrifuge for 1 min at 10,000 x g. Discard the flow-through.
      </p>
      <p>
-         Add 750 µl of DNA Wash buffer to the PerfectBind DNA Column in the Collection tube and centrifuge for 1 min at 10000 x g. Discard the flow-through. Repeat
+         Add 750 µl of DNA Wash buffer to the PerfectBind DNA Column in the Collection tube and centrifuge for 1 min at 10,000 x g. Discard the flow-through. Repeat
          this step to obtain optimum results.
      </p>
      <p>
-         Place the PerfectBind DNA Column in the Collection tube and centrifuge for 2 min at 10000 x g to dry the column matrix. This step is essential to remove
+         Place the PerfectBind DNA Column in the Collection tube and centrifuge for 2 min at 10,000 x g to dry the column matrix. This step is essential to remove
          ethanol from the column.
      </p>
      <p>
          Place the PerfectBind DNA Column into a fresh 1.5 ml Eppendorf tube. Add 50 µl of pre-warmed sterile deionized water directly to the binding matrix in the
-         PerfectBind DNA Column and centrifuge for 1 min at 5000 x g to elute the DNA.
+         PerfectBind DNA Column and centrifuge for 1 min at 5,000 x g to elute the DNA.
      </p>
      <p>
@@ Line 675: / Line 800: @@
      <p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; pH 7.5 with acetic acid</p>
      <p>Buffer RF2 (80 ml):&nbsp; 1.6 ml MOPS (0.5 M) stock solution</p>
-     <p>&nbsp; PH 6.8 with NaOH</p>
+     <p>&nbsp; pH 6.8 with NaOH</p>
      <p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 0.096 g RbCl</p>
      <p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 0.88 g CaCl<sub>2</sub>.2H<sub>2</sub>O</p>
@@ Line 681: / Line 806: @@
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Inoculate a 4 ml culture either with a single colony or with a cryoculture of the desired <em>E.coli </em>strainand incubate the culture with agitation overnight at 37&deg;C</p>
      <p><sub>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </sub>Inoculate a 300 ml shake flask containing 100 ml LB medium with the overnight culture to an OD<sub>600</sub>&nbsp; of 0.05 and grow the culture at 37&deg;C until the OD<sub>600</sub>is about 0.3</p>
-     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Transfer the cells into two 50 ml falcon tubes, incubate the cultures for 15 minues on ice and harvest the cells by centrifugation for 15 min at 5000 rpm and 4&deg;C. Discard the supernatants.</p>
+     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Transfer the cells into two 50 ml falcon tubes, incubate the cultures for 15 minues on ice and harvest the cells by centrifugation for 15 min at 5,000 rpm and 4&deg;C. Discard the supernatants.</p>
-     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Resuspend the cells in 1/3 of the original volume (~16 ml/50 ml) of buffer RF1, incubate the cells again on ice and harvest the cells by centrifugation for 15 min at 5000 rpm and 4&deg;C. Discard the supernatants.</p>
+     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Resuspend the cells in 1/3 of the original volume (~16 ml/50 ml) of buffer RF1, incubate the cells again on ice and harvest the cells by centrifugation for 15 min at 5,000 rpm and 4&deg;C. Discard the supernatants.</p>
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Resuspend the cells in 4 ml of buffer RF2 and incubate the suspensions for 15 min on ice. Prepare the Eppendorf tubes and liquid nitrogen.</p>
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Put 0.4 ml of the cell suspension into the Eppendorf reaction tubes and freeze the cells by transferring them immediately to the liquid nitrogen. Store the competent cells at -80&deg;C</p>
@@ Line 708: / Line 833: @@
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Inoculate a 20 ml culture either with a single colony or with the cryoculture of the desired <em>E.coli </em>strainand incubate the culture with agitation for 20 h at 28&deg;C</p>
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Inoculate a 250 ml SOB medium supplemented in a 2 l shake flask and grow the cells to an OD<sub>600</sub>&nbsp; of 0.5- 0.9 (20-20 h) at 18&deg;C and 200-250 rpm</p>
-     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Incubate the whole flask for 10 min on ice. Collect the cells by centrifugation for 10 min at 4&deg;C and 5000 rpm. Resuspend the cells in 80 ml of ice-cold TB and incubate them for 10 min on ice. Collect the cells by centrifugation for 5 min at 5000 rpm.</p>
+     <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Incubate the whole flask for 10 min on ice. Collect the cells by centrifugation for 10 min at 4&deg;C and 5000 rpm. Resuspend the cells in 80 ml of ice-cold TB and incubate them for 10 min on ice. Collect the cells by centrifugation for 5 min at 5,000 rpm.</p>
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Resuspend the cells in a 20 ml of ice-cold TB. Add DMSO to a final concentration of 7% (1.4 ml) and gently shake the falcon tube.</p>
      <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Transfer 0.2 ml aliquots into labelled eppendorf reaction tubes and freeze the cells in liquid nitrogen. Store the cells at &ndash;80&deg;C.</p>
@@ Line 721: / Line 846: @@
 <p>&nbsp;</p>
 <p><strong>Protocol as distributed by iGEM (modified) </strong></p>
-<p>Spin down the DNA tubes from the Transformation Efficiency Kit to collect all of the DNA into the bottom of each tube prior to use. A quick spin of 20-30 seconds at 8,000-10,000 rpm will be sufficient. Note: There should be 50 &micro;L of DNA in each tube sent in the Kit.</p>
+<p>Spin down the DNA tubes from the Transformation Efficiency Kit to collect all of the DNA into the bottom of each tube prior to use. A quick spin of 20-30 seconds at 8000-10000 rpm will be sufficient. Note: There should be 50 &micro;L of DNA in each tube sent in the Kit.</p>
 <p>Thaw competent cells on ice. Label one 2.0 ml microcentrifuge tube for each concentration and then pre-chill by placing the tubes on ice.</p>
 <p>Pipet 1 &micro;L of DNA into each microcentrifuge tube. For each concentration, use a separate tube.</p>
@@ Line 730: / Line 855: @@
 <p>Pipet 20 &micro;L from each tube onto the appropriate plate, and spread the mixture evenly across the plate. Do triplicates (3 each) of each tube if possible, so you can calculate an average colony yield. Incubate at 37&deg;C overnight. Position the plates so the agar side is facing up, and the lid is facing down.</p>
 <p>Count the number of colonies on a light field or a dark background, such as a lab bench. Use the following equation to calculate your competent cell efficiency. If you've done triplicates of each sample, use the average cell colony count in the calculation.</p>
-<p>(colonies on plate) / ng of DNA plated x 1000ng/&micro;g</p>
+<p>(colonies on plate) / ng of DNA plated x 1,000ng/&micro;g</p>
 <p>Note: The measurement "ng of DNA plated" refers to how much DNA was plated onto each agar plate, not the total amount of DNA used per transformation. You can calculate this number using the following equation:</p>
 <p>1 &micro;L x concentration of DNA (refer to vial) x (volume plated / total reaction volume)</p>
@@ Line 740: / Line 865: @@
 <h2> Protein Extraction and Purification</h2>
-<a href="" onClick=" $('#menu29').slideToggle(300, function callback() {  }); return false;"><h1 style="color:white;">Protein Extraction (French Press) and Purification (Protino® Ni-IDA 2000 His-Tag protein purification, Macherey-Nagel)</h1></a>
+<a href="" onClick=" $('#menu36').slideToggle(300, function callback() {  }); return false;"><h1 style="color:white;"> Induction, harvest and disruption of expression cultures</h1></a>
+<div id="menu36">
+<p>
+    <u>Induction</u>
+</p>
+<p>
+Recombinant protein expression was exclusively realized in <em>E.coli</em>. pET101-ScaA was expressed in BL21(DE3) cells under the control of the    <em>lac</em> operon, and pBAD-RFP-ACEL (and all other pBAD constructs) was expressed in TOP 10 cells under the control of the <em>ara</em> operon. The
+    procedure is as follows:<u></u>
+</p>
+<p>
+    Inoculate “fat” LB expression medium, having a volume corresponding to 5 % of the shake flask that is used, with 5 % (v/v) of an overnight LB starter
+    culture grown at 37°C and 150 rpm.
+</p>
+<p>
+    Incubate the expression culture at 37°C and 150 rpm until an OD<sub>600</sub> between 2.5 and 3.5 is reached.
+</p>
+<p>
+    Induce protein expression by adding the appropriate inducer to the expression culture. In case of pET101-ScaA use 1 mM IPTG and in case of pBAD-RFP-ACEL
+    use 0.2 % (v/v) L-arabinose.
+</p>
+<p>
+    Incubate the expression culture for 20 h at 37°C and 150 rpm.
+</p>
+<p>
+    Take a 1 ml sample before induction and before cell harvesting in order to analyze the expression effectivity of target proteins by SDS-PAGE.
+</p>
+<p>
+    <u>Cell Harvest</u>
+</p>
+<p>
+    Pellet the culture at 4°C, 13000rpm for 20min (SLA-3000 rotor, Sorvall).
+</p>
+<p>
+    Resuspend and wash with an equal volume of LEW Buffer (see Protein extraction).
+</p>
+<p>
+    Repeat previous centrifugation step.
+</p>
+<p>
+    Freeze pellet until further use or prepare for French Press.
+</p>
+<p>
+    <u>Cell extraction by French Press</u>
+</p>
+<p>
+    Resuspend pellet in 20mL 1x LEW Buffer .
+</p>
+<p>
+    Take a small sample (10µl) for microscopy.
+</p>
+<p>
+    Disrupt cells by using a discontinuous high-pressure homogenizer (e.g., French-Press, 4 cycles at 1000 psi).
+</p>
+<p>
+    take a small sample (10µl) and analyse both before and after press samples under the microscope. Look for inclusion bodies.
+</p>
+<p>
+    Sediment cell debris via centrifugation for 30 min at 13000 rpm (SS-34 rotor, Sorvall) and 4°C.
+</p>
+<p>
+    Filter the resulting supernatant through 0.45 µm sterile filters and subsequently apply it <a name="_GoBack"></a>to chromatographic purification steps.
+</p>
+</div>
+<a href="" onClick=" $('#menu29').slideToggle(300, function callback() {  }); return false;"><h1 style="color:white;">Protein Purification (Protino® Ni-IDA 2000 His-Tag protein purification, Macherey-Nagel)</h1></a>
 <div id="menu29">
 <ul>
@@ Line 753: / Line 942: @@
              </td>
              <td valign="top" width="97">
-                 <p>7.8g</p>
+                 <p>7.8 g</p>
              </td>
          </tr>
@@ Line 761: / Line 950: @@
              </td>
              <td valign="top" width="97">
-                 <p>17.5g</p>
+                 <p>17.5 g</p>
              </td>
          </tr>
@@ Line 769: / Line 958: @@
              </td>
              <td valign="top" width="97">
-                 <p>ad. 1000mL</p>
+                 <p>ad. 1000 mL</p>
              </td>
          </tr>
@@ Line 784: / Line 973: @@
              </td>
              <td valign="top" width="97">
-                 <p>7.8g</p>
+                 <p>7.8 g</p>
              </td>
          </tr>
@@ Line 792: / Line 981: @@
              </td>
              <td valign="top" width="97">
-                 <p>17.5g</p>
+                 <p>17.5 g</p>
              </td>
          </tr>
@@ Line 800: / Line 989: @@
              </td>
              <td valign="top" width="97">
-                 <p>17.0g</p>
+                 <p>17.0 g</p>
              </td>
          </tr>
@@ Line 808: / Line 997: @@
              </td>
              <td valign="top" width="97">
-                 <p>ad. 1000mL</p>
+                 <p>ad. 1,000 mL</p>
              </td>
          </tr>
@@ Line 816: / Line 1,005: @@
 <p>Adjust to pH 8.0 using NaOH.</p>
 <p>&nbsp;</p>
-<p><strong>1.) Cell extraction by French Press:</strong></p>
-<p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Resuspend pellet in 20mL 1x LEW Buffer from the kit</p>
+<p><strong>Protino&reg; Ni-IDA 2,000 His-Tag protein purification (Macherey-Nagel)</strong></p>
-<p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Take a small sample (10&micro;l) for microscopy</p>
+<p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Wet Ni-IDA column with 4 mL of 1x LEW buffer and discard flow through</p>
-<p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Press 4 times with a French Press at High Pressure and collect the flow through</p>
-<p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Take a small sample (10&micro;l) and analyse both before and after press samples under the microscope. Look for inclusion bodies.</p>
-<p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Centrifuge pressed samples at 4&deg;C and 13000 rpm for 45 minutes, keep supernatant</p>
-<p>&nbsp;</p>
-<p><strong>2.) Protino&reg; Ni-IDA 2000 His-Tag protein purification (Macherey-Nagel)</strong></p>
-<p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Wet Ni-IDA column with 4mL of 1x LEW buffer and discard flow through</p>
 <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Run supernatant from the cell extraction through the column and collect flow through (cell extract, store at 4&deg;C)</p>
-<p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Wash column 3 times with 4ml 1x LEW Buffer</p>
+<p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Wash column 3 times with 4 mL 1x LEW Buffer</p>
 <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Collect each flow through (wash 1-3) and store at 4&deg;C</p>
-<p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Elute protein 3 times with 3mL Elution Buffer (contains Imidazole)</p>
+<p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Elute protein 3 times with 3 mL Elution Buffer (contains Imidazole)</p>
 <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Collect each elution and store fractions at 4&deg;C</p>
 <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Quantify protein content by Bradford measurement (see Bradford assay)</p>
+</div>
+<a href="" onClick=" $('#menu34').slideToggle(300, function callback() {  }); return false;"><h1 style="color:white;"> Affinity chromatography of His-tagged proteins</h1></a>
+<div id="menu34">
+<p>
+    The N-terminal His<sub>6</sub>- tagged fusion proteins His<sub>6</sub>-ScaA and His<sub>6</sub>-RFP-ACEL were purified by nickel affinity chromatography
+    using Ni-NTA-agarose columns in a first purification step.
+</p>
+<p>
+    <u>Preparation:</u>
+</p>
+<p>
+    Connect a 5 ml HisTrap FF column (GE Healthcare) to an Äkta purifier or Äkta prime system and wash the column with 1 CV (column volume) 20 % EtOH and a
+    maximum flow rate of 3 ml/min.
+</p>
+<p>
+    Pre-equilibrate the column with lysis buffer by first washing 3 CV with water, followed by 3 CV with buffer, each with a maximum flow rate of 5 ml/min.
+</p>
+<p>
+    <u>Run:</u>
+</p>
+<p>
+.) Load the protein solution onto the column using an appropriate super loop (10 ml or 50 ml) and a maximum flow rate of 1 ml/min. Start the automated
+    fractionation system.
+</p>
+<p>
+.) Once the protein is loaded, wash the column with lysis buffer using a maximum flow rate of 5 ml/min until the UV absorption has reached a constant
+    value.
+</p>
+<p>
+.) Start eluting unspecifically bound, contaminative protein species with a flow rate of 3 ml/min by applying a stepwise gradient from 0 % to 2 % of
+    elution buffer.
+</p>
+<p>
+.) Elute the target protein with a flow rate of 3 ml/min by applying a linear gradient from 2 % to 50 % of elution buffer over 20 CV (column volumes).
+</p>
+<p>
+.) Analyze obtained peak fractions by SDS-PAGE and pool the fractions containing the target protein.
+</p>
+<p>
+.) Reduce the volume of the protein solution via concentration until a maximum volume of 5 ml is reached and apply it to size exclusion chromatography.
+</p>
+<p>
+    All chromatographical purification steps are carried out at 20°C.
+</p>
+<p>
+    Required buffers
+</p>
+<p>
+    Buffer A: Lysis buffer (20 mM phosphate pH 8, 500 mM NaCl, 5 % (v/v) glycerol, 1 mM 2-mercaptoethanol)
+</p>
+<p>
+    Buffer B: Elution buffer (Lysis buffer supplemented with 250 mM imidazole)
+</p>
+</div>
+<a href="" onClick=" $('#menu39').slideToggle(300, function callback() {  }); return false;"><h1 style="color:white;"> Size Exclusion Chromatography</h1></a>
+<div id="menu39">
+<p>
+    In a second purification step, the target proteins ScaA and RFP-ACEL were separated according to their size (radius of gyration) by employing size
+    exclusion chromatography. Therefore:
+</p>
+<p>
+    Connect a HiLoad Superdex 200 16/600 column (GE Healthcare) to an Äkta purifier or Äkta prime system and wash the column with 1 CV of 20 % EtOH and a
+    maximum flow rate of 1 ml/min.
+</p>
+<p>
+    Pre-equilibrate the column with loading buffer by washing first with 1 CV of water and subsequently with 1 CV of the respective buffer, each with a maximum
+    flow rate of 1 ml/min.
+</p>
+<p>
+    Load the concentrated protein solution with a maximum flow rate of 1 ml/min onto the column by using a 5 ml sampling loop. Start the automated
+    fractionation.
+</p>
+<p>
+    Elute the target protein with a maximum flow rate of 1 ml/min and analyze obtained peak fractions on a SDS gel.
+</p>
+<p>
+    Pool the fractions containing the target protein.
+</p>
+<p>
+    All chromatographic purification steps are carried out at room temperature.
+</p>
+<p>
+    Required buffer:
+</p>
+<p>
+    Buffer A: Loading buffer (20 mM phosphate pH 8, 500 mM NaCl, 5 % glycerol, 1 mM 2-mercaptoethanol)
+</p>
+</div>
+<a href="" onClick=" $('#menu35').slideToggle(300, function callback() {  }); return false;"><h1 style="color:white;"> Concentration of protein solutions</h1></a>
+<div id="menu35">
+<p>
+    Concentration of protein solutions was realized via centrifugation using 20 ml Vivaspin centrifugal concentrators (Viva Science) with the appropriate
+    molecular weight cutoffs of 50 kDa in case of the scaffolding protein ScaA and 30 kDa in case of RFP-ACEL. In order to concentrate protein solutions:
+</p>
+<p>
+    Wash the concentrator with 20 ml of buffer in order to remove the protectant (glycerol) from the membrane.
+</p>
+<p>
+    Add the protein sample to the concentrator and start centrifugation at 4°C until the desired volume/concentration is reached. The sample volume and the
+    speed is determined by the rotor that is used. If a 25° fixed angle rotor is applied, the maximum starting volume is 14 ml and the speed is restricted to
+x g.
+</p>
+<p>
+    Gently mix the upper reservoir prior to each refilling step and prior to transfer.
+</p>
+<p>
+    Check the flow through for leakage by Bradford assay.
+</p>
 </div>
@@ Line 854: / Line 1,149: @@
 <p>&nbsp;</p>
 <p>Calculation of protein concentration:</p>
+</html>
+[[File:Bradford_calculation_iGEM_Goettingen_2015.jpeg|thumb|center|300px|<p style="text-align: justify;">Formula for calculating the protein concentration</p>]]
+<html>
 <p><br /> &nbsp;</p>
 <p>&nbsp;</p>
@@ Line 859: / Line 1,159: @@
 </div>
+<a href="" onClick=" $('#menu38').slideToggle(300, function callback() {  }); return false;"><h1 style="color:white;"> SDS Polyacrylamid Gel Electrophoresis</h1></a>
+<div id="menu38">
+<p>
+    The analytic protein separation according to the apparent molecular weight was carried out by discontinuous SDS polyacrylamid gel electrophoresis according
+    to Laemmli (1970) using mini gel electrophoresis chambers (BioRad, 10x8 cm). For cast and run of the gels do the following:
+</p>
+<p>
+    For the stacking gel use the following components: 0.25 % of the total volume of stacking gel buffer, and acrylamid to a final concentration of 4 %. Add
+    water to the final volume (cf. pipetting scheme). Add 1/133 of the total volume of 10 % ammonium persulfate (APS) and 1/1000 of
+    N,N,N’,N’-tetramethyl-ethylenediamine (TEMED).
+</p>
+<p>
+    For the separation gel mix the appropriate amount of acrylamid (e.g. 10 % for a 10 % SDS gel) with 0.25 % of the final volume of separation gel buffer and
+    fill with water to the final volume. Add 1/133 of the total volume of 10 % APS and 1/1000 of TEMED.
+</p>
+<p>
+    Place the poured gel into the running chamber and fill the upper and lower reservoir with running buffer.
+</p>
+<p>
+    Dilute the protein samples 1:1 with loading buffer and load the gel.
+</p>
+<p>
+    Run the gel with 15mA per gel for 15 min, and then increase to 30mA per Gel until the end.
+</p>
+<p>
+    After electrophoretic separation, place the gels into staining solution and heat it without boiling.
+</p>
+<p>
+    Incubate the gels under slow agitation until protein bands become visible.
+</p>
+<p>
+    Discolor the gels by using fixation solution.
+</p>
+<p>
+    <strong>Pipetting scheme. </strong>
+</p>
+<table border="1" cellspacing="0" cellpadding="0">
+    <tbody>
+        <tr>
+            <td width="212" valign="top">
+                <p align="center">
+                    <strong>Compoment</strong>
+                </p>
+                <p align="center">
+                    <strong>(For 2 gels)</strong>
+                </p>
+            </td>
+            <td width="212" valign="top">
+                <p align="center">
+                    <strong>Stacking gel</strong>
+                </p>
+                <p align="center">
+                    <strong>(4 % acrylamid)</strong>
+                </p>
+            </td>
+            <td width="212" valign="top">
+                <p align="center">
+                    <strong>Separation gel</strong>
+                </p>
+                <p align="center">
+                    <strong>(10 % acrylamid)</strong>
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="212" valign="top">
+                <p align="center">
+                    Water
+                </p>
+            </td>
+            <td width="212" valign="top">
+                <p align="center">
+.64 ml
+                </p>
+            </td>
+            <td width="212" valign="top">
+                <p align="center">
+ml
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="212" valign="top">
+                <p align="center">
+                    Acrylamid
+                </p>
+            </td>
+            <td width="212" valign="top">
+                <p align="center">
+.4 ml
+                </p>
+            </td>
+            <td width="212" valign="top">
+                <p align="center">
+ml
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="212" valign="top">
+                <p align="center">
+                    Stacking gel buffer
+                </p>
+            </td>
+            <td width="212" valign="top">
+                <p align="center">
+.96 ml
+                </p>
+            </td>
+            <td width="212" valign="top">
+                <p align="center">
+                    ---
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="212" valign="top">
+                <p align="center">
+                    Separation gel buffer
+                </p>
+            </td>
+            <td width="212" valign="top">
+                <p align="center">
+                    ---
+                </p>
+            </td>
+            <td width="212" valign="top">
+                <p align="center">
+ml
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="636" colspan="3" valign="top">
+                <p align="center">
+                    <strong>Mix</strong>
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="212" valign="top">
+                <p align="center">
+% APS
+                </p>
+            </td>
+            <td width="212" valign="top">
+                <p align="center">
+µl
+                </p>
+            </td>
+            <td width="212" valign="top">
+                <p align="center">
+µl
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="212" valign="top">
+                <p align="center">
+                    TEMED
+                </p>
+            </td>
+            <td width="212" valign="top">
+                <p align="center">
+µl
+                </p>
+            </td>
+            <td width="212" valign="top">
+                <p align="center">
+µl
+                </p>
+            </td>
+        </tr>
+    </tbody>
+</table>
+<p>
+    Required agents and solutions:
+</p>
+<p>
+% Acrylamid/bis-acrylamid (37.5:1)
+</p>
+<p>
+% (w/v) SDS solution
+</p>
+<p>
+    Stacking gel buffer (1.5 M Tris/HCl pH 8.8, 0.4 % (w/v) SDS)
+</p>
+<p>
+    Separation gel buffer (0.5 M Tris/HCl pH 6.5, 0.4 % (w/v) SDS)
+</p>
+<p>
+x Laemmli loading buffer (20 mM Tris/HCl pH 6.5, 4 % (w/v) SDS, 10 % (v/v) β-mercaptoethanol, 40 % (v/v) glycerol, 0.002 % (w/v) bromphenol blue)
+</p>
+<p>
+x SDS running buffer (25 mM Tris base, 192 mM glycine, 0.1 % (w/v) SDS)
+</p>
+<p>
+    Staining solution (0.005 % (w/v) Coomassie Brilliant Blue G-250, 0.0025 % (w/v) Coomassie Brilliant Blue R-250, 10 % (v/v) ethanol und 5 % (v/v) acetic
+    acid)
+</p>
+<p>
+    Fixation solution (10 % (v/v) acetic acid)
+</p>
+</div>
-<h2> Activity Screens </h2>
+<a href="" onClick=" $('#menu40').slideToggle(300, function callback() {  }); return false;"><h1 style="color:white;"> Western Blot</h1></a>
-                     <a href="" onClick=" $('#menu9').slideToggle(300, function callback() {  }); return false;"><h1>Esterase activity test</h1></a>
+<div id="menu40">
+<p>
+x TBS Buffer (store at RT)
+</p>
+<table border="1" cellspacing="0" cellpadding="0">
+    <tbody>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    Tris HCL (MW: 121,14 g/mol)
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+.057g
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    NaCl (MW: 58.44 g/mol)
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+.91g
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    H<sub>2</sub>O dest.
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+                    ad. 500 ml
+                </p>
+            </td>
+        </tr>
+    </tbody>
+</table>
+<p>
+    adjust to pH 7.4
+</p>
+<p>
+x Transfer Buffer (store at RT)
+</p>
+<table border="1" cellspacing="0" cellpadding="0">
+    <tbody>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    Tris
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+.029 g
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    Glycin
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+,41g
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    Methanol
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+ml
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    H<sub>2</sub>O bidest.
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+                    ad. 1000ml
+                </p>
+            </td>
+        </tr>
+    </tbody>
+</table>
+<p>
+    check pH: 8.1-8.4
+</p>
+<p>
+    If the pH is not correct, the Buffer has to be remade. Do not adjust.
+</p>
+<p>
+x TBS-Tween Buffer (store at RT)
+</p>
+<table border="1" cellspacing="0" cellpadding="0">
+    <tbody>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    Tris-HCL (MW: 121.14 g/mol)
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+.057g
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    NaCl (MW: 58.44 g/mol)
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+.91g
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    Tween20 (Endkonz. 0,1%)
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+.5ml
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    H<sub>2</sub>O bidest.
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+                    ad. 500ml
+                </p>
+            </td>
+        </tr>
+    </tbody>
+</table>
+<p>
+    adjust to pH 7.4
+</p>
+<p>
+    Blocking Solution
+</p>
+<table border="1" cellspacing="0" cellpadding="0">
+    <tbody>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    Skim Milk
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+,5g
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+x TBS
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+ml
+                </p>
+            </td>
+        </tr>
+    </tbody>
+</table>
+<p>
+    Dissolve for 15-30 min at RE. Store 400µl at 4°C for a later step.
+</p>
+<p>
+    Phosphatase Buffer (store at RT)
+</p>
+<table border="1" cellspacing="0" cellpadding="0">
+    <tbody>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    Tris-HCL (MW: 121.14 g/mol)
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+.057g
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    NaCl (MW: 58.44 g/mol)
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+.922 g
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    MgCl<sub>2 </sub>x 6 H<sub>2</sub>O (MW: 203.3 g/mol)
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+.51 g
+                </p>
+            </td>
+        </tr>
+        <tr>
+            <td width="307" valign="top">
+                <p>
+                    H<sub>2</sub>O bidest.
+                </p>
+            </td>
+            <td width="307" valign="top">
+                <p>
+                    ad. 500ml
+                </p>
+            </td>
+        </tr>
+    </tbody>
+</table>
+<p>
+    adjust to pH 9.5
+</p>
+<p>
+    Antibody: Anti V5-AP Antibody (Invitrogen, store at 4°C)
+</p>
+<p>
+    NBT: Promega, 50 mg/ml, store at -20°C
+</p>
+<p>
+    BCIP: Promega, 50 mg/ml, store at -20°C
+</p>
+<p>
+.) Run an SDS Gel and use Protein Ladder compatible with Western Blots.
+</p>
+<p>
+.) Use Perfect Blue Semi-Dry Electro blotter from Peqlab and assemble apparatus in a tip box with a little transfer buffer (sandwich should be moist    <u>not </u>wet):
+</p>
+<p>
+    Base of blotter = Kathode (+) bottom
+</p>
+<p>
+x Whatman paper (moist) size of SDS page
+</p>
+<p>
+    Blotting membrane (Hybond EHL, 0,45µm, moist, no bubbles, SDS page sized)
+</p>
+<p>
+    SDS Gel (no bubbles! Proteins have a neg. charge and go towards the Kathode)
+</p>
+<p>
+x Whatman paper (moist, gel sized)
+</p>
+<p>
+    Lid = Anode (-) top
+</p>
+<p>
+    After assembly of the sandwich the lid is screwed on lightly with 3 screws. Connect Blotter to an adequate power supply, which can work at a constant 10V.
+    Blot at 200mA per Gel and constant 10V for 1 hour.
+</p>
+<p>
+.) Wash the membrane 3x 5 min with 1x TBS Buffer on a rocker
+</p>
+<p>
+.) Block membrane in 50ml 1 x TBS Buffer with 5% skim milk for one hour or overnight on a rocker.
+</p>
+<p>
+.) Wash 3x 15min 1xTBS-Tween on a rocker
+</p>
+<p>
+.) Prepare Antibody: 14ml 1xTBS-Tween + 200µl 1x TBS Puffer/5% Skimmilk + 7µl Antibody
+</p>
+<p>
+.) Incubate with antibody for 2 hours on a rocker
+</p>
+<p>
+.) Wash 2x shortly in 1x TBS-Tween Buffer on a rocker
+</p>
+<p>
+.) 1x 15min 1x TBS-Tween Buffer on the rocker
+</p>
+<p>
+.) 2x 5min 1x TBS-Tween Buffer on the rocker
+</p>
+<p>
+.) Wash 2x 10 min 1x TBS Buffer on a rocker
+</p>
+<p>
+.) Wash 2x shortly in 1x Phosphatse buffer
+</p>
+<p>
+.) 10ml 1x Phosphatase buffer + 66µl NBT + 33µl BCIP
+</p>
+<p>
+    - stain in the dark until bands become visible
+</p>
+<p>
+    - stop the reaction by washing with H2O
+</p>
+<p>
+    - dry western blot in Whatman Paper
+</p>
+<p>
+.) Scan the membrane
+</p>
+</div>
+<h2> Activity Screens & Tests</h2>
+                     <a href="" onClick=" $('#menu9').slideToggle(400, function callback() {  }); return false;"><h1>Esterase activity test</h1></a>
 <div id="menu9">
      <p>Materials:</p>
-     <p>Substrate- 1mM 4-nitrophenyl butyrate prepared in Na-Phosphate buffer (pH8.0)</p>
+     <p>Substrate- 1mM 4-nitrophenyl butyrate prepared in Na-Phosphate buffer (pH 8.0)</p>
      <p>Protein sample</p>
      <p>Procedure:</p>
@@ Line 874: / Line 1,721: @@
      <p>&nbsp;</p>
 </div>
+ <a href="" onClick=" $('#menu31').slideToggle(400, function callback() {  }); return false;"><h1>Phosphatase activity test</h1></a>
+<div id="menu31">
+<p><strong>Materials:</strong></p>
+<ul>
+    <li>Freshly prepared AAM Solution (Acetone, 5N H<sub>2</sub>SO<sub>4</sub>, 10 mM Ammonium molybdate, 2:1:1 v/v)</li>
+    <li>50 mM Sodium acetate buffer, pH 5.0</li>
+    <li>100 mM Pyrophosphate</li>
+    <li>1 M Citric acid</li>
+    <li>Protein sample</li>
+</ul>
+<p><strong>Procedure:</strong></p>
+<ul>
+    <li>Set a heating block to 37&deg;C or 40&deg;C</li>
+    <li>Place 2 mL reaction tubes for each sample (technical triplicates) plus one blank in the heating block</li>
+    <li>Pipet 250 &micro;L of 50mM Sodium acetate buffer in all reaction tubes</li>
+    <li>Add 40 &micro;L of protein sample</li>
+    <li>Add 10 &micro;L of 100 mM Pyrophosphate to the tubes</li>
+    <li>Mix the tubes by inverting</li>
+    <li>Incubate on the heating block for 30 minutes</li>
+    <li>Add 1.5 mL of AAM solution and homogenize by inverting the tubes</li>
+    <li>Add 100 &micro;L 1 M Citric acid</li>
+    <li>If phosphatase is present, the colour will change from white/transparent to yellow</li>
+    <li>Measure the colour strength in a photometer at 355 nm</li>
+</ul>
+<p>CAUTION: Make sure that the buffer you used for protein extraction does not contain any phosphate components. Otherwise the test will be false positive!</p>
+</div>
 <a href="" onClick=" $('#menu13').slideToggle(300, function callback() {  }); return false;">
@@ Line 886: / Line 1,760: @@
      <li>Incubate plates at 37<sup>o</sup>C for minimum 3-4 days (timing can be extended depending on bacterial strain).</li>
      <li>After 3-4 days look for plates having clear zone of activity around cellulose substrate.</li>
+</div>
+<a href="" onClick=" $('#menu41').slideToggle(300, function callback() {  }); return false;"><h1 style="color:white;"> Enzymatic Activity Test for Cellulase </h1></a>
+<div id="menu41">
+<p>
+    Solutions:
+</p>
+<p>
+    Buffer:
+</p>
+<p>
+    Tris (MW: 121.14 g/mol) 50 mM
+</p>
+<p>
+    dH<sub>2</sub>O ad 1 l
+</p>
+<p>
+    pH 7
+</p>
+<p>
+    Substrate solution:
+</p>
+<p>
+    Carboxymethil cellulose 1 % (w / v)
+</p>
+<p>
+    ddH<sub>2</sub>O ad 1 l
+</p>
+<p>
+    DNSA reagent solution:
+</p>
+<p>
+    Dinitrosalycylic acid 10 g
+</p>
+<p>
+    Phenol 2 ml
+</p>
+<p>
+    K Na Tartrate 200 g
+</p>
+<p>
+    NaOH 10 g
+</p>
+<p>
+    Na<sub>2</sub>SO<sub>3</sub> 0.5 g
+</p>
+<p>
+    dH<sub>2</sub>O ad 1 l
+</p>
+<p>
+    Store at 4°C, protected from light
+</p>
+<p>
+    Procedure:
+</p>
+<p>
+µl substrate solution
+</p>
+<p>
+µl Tris-Buffer
+</p>
+<p>
+    x µl enzyme solution
+</p>
+<p>
+    ad 500 µl ddH<sub>2</sub>O
+</p>
+<p>
+    Incubate setup as described above at 37°C for 20 min.
+</p>
+<p>
+    Add 750 µl DNSA. Heat the setup at 96°C for 15 min.
+</p>
+<p>
+    Put mixture on ice, centrifuge shortly at 4°C, 13000 x g.
+</p>
+<p>
+    Measure OD<sub>575</sub> against same setup without enzyme as a blank.
+</p>
 </div>
@@ Line 965: / Line 1,920: @@
              </td>
              <td valign="top">
-                 <p>2&micro;l&nbsp;&nbsp;</p>
+                 <p>2 &micro;l&nbsp;&nbsp;</p>
              </td>
          </tr>
@@ Line 973: / Line 1,928: @@
              </td>
              <td valign="top">
-                 <p>1&micro;l&nbsp;</p>
+                 <p>1 &micro;l&nbsp;</p>
              </td>
          </tr>
@@ Line 1,007: / Line 1,962: @@
 <p></p>
 <ul>
-     <li>For 10 &micro;l&nbsp;reaction add 1 &micro;l&nbsp; of 10x Tango buffer , for 20 &micro;l&nbsp;reaction add 2 &micro;l&nbsp; of 10x Tango buffer and vice versa.</li>
+     <li>For 10 &micro;l&nbsp;reaction add 1 &micro;l&nbsp; of 10x Tango buffer, for 20 &micro;l&nbsp;reaction add 2 &micro;l&nbsp; of 10x Tango buffer and vice versa.</li>
      <li>Incubate at 37 <sup>o</sup>C for 2 hours.</li>
-     <li>For inactivation incubation at 80&deg;C for 5min.&nbsp;&nbsp;</li>
+     <li>For inactivation incubation at 80&deg;C for 5 min.&nbsp;&nbsp;</li>
      <li>Check the products on 0.8% agarose gel.</li>
 </ul>
@@ Line 1,030: / Line 1,985: @@
              </td>
              <td valign="top" width="96">
-                 <p>500-1000 ng</p>
+                 <p>500-1,000 ng</p>
              </td>
          </tr>
@@ Line 1,089: / Line 2,044: @@
              </td>
              <td valign="top">
-                 <p>500-1000 ng</p>
+                 <p>500-1,000 ng</p>
              </td>
          </tr>
@@ Line 1,243: / Line 2,198: @@
              </td>
              <td valign="top" width="301">
-                 <p>1000 ng (2 &micro;l)</p>
+                 <p>1,000 ng (2 &micro;l)</p>
              </td>
          </tr>
@@ Line 1,251: / Line 2,206: @@
              </td>
              <td valign="top" width="301">
-                 <p>1&micro;l</p>
+                 <p>1 &micro;l</p>
              </td>
          </tr>
@@ Line 1,283: / Line 2,238: @@
              </td>
              <td valign="top">
-                 <p>15&micro;l</p>
+                 <p>15 &micro;l</p>
              </td>
          </tr>
@@ Line 1,291: / Line 2,246: @@
              </td>
              <td valign="top">
-                 <p>2&micro;l</p>
+                 <p>2 &micro;l</p>
              </td>
          </tr>
@@ Line 1,299: / Line 2,254: @@
              </td>
              <td valign="top">
-                 <p>2&micro;l</p>
+                 <p>2 &micro;l</p>
              </td>
          </tr>
@@ Line 1,307: / Line 2,262: @@
              </td>
              <td valign="top">
-                 <p>1&micro;l</p>
+                 <p>1 &micro;l</p>
              </td>
          </tr>
@@ Line 1,315: / Line 2,270: @@
              </td>
              <td valign="top">
-                 <p>1&micro;l</p>
+                 <p>1 &micro;l</p>
              </td>
          </tr>
@@ Line 1,321: / Line 2,276: @@
 </table>
 <p>&nbsp;</p>
-<p>Incubate 20min at 37˚C and inactivate 5min at 80˚C.</p>
+<p>Incubate 20 min at 37˚C and inactivate 5 min at 80˚C.</p>
 <p>&nbsp;</p>
      <p></p>
@@ Line 1,414: / Line 2,369: @@
                  </td>
                  <td valign="top" width="57">
-                     <p>12ul</p>
+                     <p>12 ul</p>
                  </td>
              </tr>
@@ Line 1,422: / Line 2,377: @@
                  </td>
                  <td valign="top" width="57">
-                     <p>2ul</p>
+                     <p>2 ul</p>
                  </td>
              </tr>
@@ Line 1,430: / Line 2,385: @@
                  </td>
                  <td valign="top" width="57">
-                     <p>2ul</p>
+                     <p>2 ul</p>
                  </td>
              </tr>
@@ Line 1,438: / Line 2,393: @@
                  </td>
                  <td valign="top" width="57">
-                     <p>0,5ul</p>
+                     <p>0.5 µl</p>
                  </td>
              </tr>
@@ Line 1,446: / Line 2,401: @@
                  </td>
                  <td valign="top" width="57">
-                     <p>1ul</p>
+                     <p>1 ul</p>
                  </td>
              </tr>
@@ Line 1,454: / Line 2,409: @@
                  </td>
                  <td valign="top" width="57">
-                     <p>1ul</p>
+                     <p>1 ul</p>
                  </td>
              </tr>
@@ Line 1,462: / Line 2,417: @@
                  </td>
                  <td valign="top" width="57">
-                     <p>1,5 ul</p>
+                     <p>1.5 µl</p>
                  </td>
              </tr>
@@ Line 1,471: / Line 2,426: @@
 <p><span style="text-decoration: underline;">&nbsp;</span></p>
 <p>-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; <span style="text-decoration: underline;">Program: </span></p>
-<p>Initial denaturalization: 98˚C, 5min.</p>
+<p>Initial denaturalization: 98˚C, 5 min</p>
-<p>Denaturalization: 96˚C, 45 seg.</p>
+<p>Denaturalization: 96˚C, 45 s</p>
-<p>Annealing: 70˚C, 30 seg.</p>
+<p>Annealing: 70˚C, 30 s</p>
-<p>Elongation: 72˚C, 25 seg.</p>
+<p>Elongation: 72˚C, 25 s</p>
      <p></p>
      <p>&nbsp;</p>
@@ Line 1,490: / Line 2,445: @@
 <ul>
 <p>This protocol describes PCR procedure using Phusion High-Fidelity DNA Polymerase. <strong>(Thermo Fisher Scientific).</strong></p>
-<p>&bull; The annealing rules are different from many common DNA polymerases (such as Taq DNA polymerases).</p>
+<p>&bull; Note: the annealing conditions depend on the applied DNA polymerases (such as Taq DNA polymerases).</p>
 <p>&bull;Use 15&ndash;30 s/kb for extension. Do not exceed 1 min/kb.</p>
 <p>&bull;Phusion DNA Polymerases produce blunt end DNA products.</p>
@@ Line 1,747: / Line 2,702: @@
              </td>
              <td valign="top" nowrap="nowrap" width="96">
-                 <p align="center">10s</p>
+                 <p align="center">10 s</p>
              </td>
              <td rowspan="3" valign="top" nowrap="nowrap" width="88">
@@ Line 1,761: / Line 2,716: @@
              </td>
              <td valign="top" nowrap="nowrap" width="96">
-                 <p align="center">15s</p>
+                 <p align="center">15 s</p>
              </td>
          </tr>
@@ Line 1,802: / Line 2,757: @@
                      <a href="" onClick=" $('#menu25').slideToggle(300, function callback() {  }); return false;"><h1> Protocol for Sanger sequencing</h1></a>
 <div id="menu25">
-<p align="center"><strong>Protocol for Sanger sequencing</strong></p>
 <ul>
      <li>Sequencing reaction setup</li>
 </ul>
-<table style="width: 541px;" border="1" cellspacing="0" cellpadding="0" align="left">
+<table style="width: 445px;" border="1" cellspacing="0" cellpadding="0" align="left">
      <tbody>
          <tr>
              <td valign="top" width="205">
-                 <p align="center"><strong>Component</strong></p>
+                 <p><strong>Template</strong></p>
              </td>
-             <td valign="top" width="174">
+             <td valign="top" width="240">
-                 <p align="center"><strong>PCR product</strong></p>
+                 <p><strong>DNA amount</strong></p>
-            </td>
-            <td valign="top" width="162">
-                <p align="center"><strong>Template quantity</strong></p>
              </td>
          </tr>
          <tr>
-             <td rowspan="8" valign="top" width="205">
+             <td valign="top" width="205">
-                 <p align="center">&nbsp;</p>
+                 <p>PCR products&nbsp;</p>
-                <p align="center">&nbsp;</p>
-                <p align="center">&nbsp;</p>
-                <p align="center">DNA</p>
              </td>
-             <td valign="top" width="174">
+             <td valign="top" width="240">
-                 <p align="center">100 - 200 bp</p>
+                 <p>10 ng/100 bp (if larger 1.5 kb 150 ng)</p>
-            </td>
-            <td valign="top" width="162">
-                <p align="center">3 &ndash; 7 ng</p>
              </td>
          </tr>
          <tr>
-             <td valign="top" width="174">
+             <td valign="top" width="205">
-                 <p align="center">200 - 500 bp</p>
+                 <p>Plasmids</p>
              </td>
-             <td valign="top" width="162">
+             <td valign="top" width="240">
-                 <p align="center">7 &ndash; 12 ng</p>
+                 <p>300 ng</p>
-            </td>
-        </tr>
-        <tr>
-            <td valign="top" width="174">
-                <p align="center">500 - 1000 bp</p>
-            </td>
-            <td valign="top" width="162">
-                <p align="center">12 &ndash; 25 ng</p>
-            </td>
-        </tr>
-        <tr>
-            <td valign="top" width="174">
-                <p align="center">1000 - 2000 bp</p>
-            </td>
-            <td valign="top" width="162">
-                <p align="center">25 &ndash; 45 ng</p>
-            </td>
-        </tr>
-        <tr>
-            <td valign="top" width="174">
-                <p align="center">&gt;2000 bp</p>
-            </td>
-            <td valign="top" width="162">
-                <p align="center">45 &ndash; 80 ng</p>
-            </td>
-        </tr>
-        <tr>
-            <td valign="top" width="174">
-                <p align="center">Double stranded</p>
-            </td>
-            <td valign="top" width="162">
-                <p align="center">500 - 1500 ng</p>
-            </td>
-        </tr>
-        <tr>
-            <td valign="top" width="174">
-                <p align="center">Single stranded</p>
-            </td>
-            <td valign="top" width="162">
-                <p align="center">250 - 500 ng</p>
-            </td>
-        </tr>
-        <tr>
-            <td valign="top" width="174">
-                <p align="center"><em>Cosmid, BAC</em></p>
-            </td>
-            <td valign="top" width="162">
-                <p align="center">2 &ndash; 4 &micro;g</p>
              </td>
          </tr>
@@ Line 1,893: / Line 2,790: @@
                  <p>Forward primer (5pmol/ &micro;l&nbsp;)</p>
              </td>
-             <td valign="top" width="174">
+             <td valign="top" width="240">
-                 <p align="center">1 &micro;l</p>
+                 <p>1 &micro;l</p>
-            </td>
-            <td rowspan="4" valign="top" width="162">
-                <p align="center">&nbsp;</p>
              </td>
          </tr>
@@ Line 1,904: / Line 2,798: @@
                  <p>Reverse primer (5pmol/ &micro;l&nbsp;)</p>
              </td>
-             <td valign="top" width="174">
+             <td valign="top" width="240">
-                 <p align="center">1 &micro;l</p>
+                 <p>1 &micro;l</p>
              </td>
          </tr>
@@ Line 1,912: / Line 2,806: @@
                  <p>Nuclease free H<sub>2</sub>O</p>
              </td>
-             <td valign="top" width="174">
+             <td valign="top" width="240">
-                 <p align="center">XX &micro;l</p>
+                 <p>ad. 5 &micro;l</p>
              </td>
          </tr>
@@ Line 1,920: / Line 2,814: @@
                  <p><strong>Total volume</strong></p>
              </td>
-             <td valign="top" width="174">
+             <td valign="top" width="240">
-                 <p align="center"><em>5 </em>&micro;l</p>
+                 <p><strong>5 </strong><strong>&micro;l</strong></p>
              </td>
          </tr>
@@ Line 1,944: / Line 2,838: @@
 <p>&nbsp;</p>
 <p>&nbsp;</p>
-<p>&nbsp;</p>
-<p>&nbsp;</p>
-<p>&nbsp;</p>
-<p>&nbsp;</p>
-<p>&nbsp;</p>
-<p>&nbsp;</p>
-<p>&nbsp;</p>
-<p>&nbsp;</p>
-<p>&nbsp;</p>
-<p>&nbsp;</p>
-<p>&nbsp;</p>
-<p>&nbsp;</p>
 <ul>
-     <li>Forward and Reverse primers should be added in 2 individual eppendorf tubes.</li>
+     <li>Forward and reverse primers should be added in 2 individual sample tubes!</li>
 </ul>
-    <p></p>
-    <p>&nbsp;</p>
-    <p></p>
-    <p>&nbsp;</p>
 </div>
@@ Line 1,990: / Line 2,868: @@
              </td>
              <td valign="top" width="84">
-                 <p>800ng</p>
+                 <p>800 ng</p>
              </td>
          </tr>
          <tr>
              <td valign="top" width="205">
-                 <p>Forward primer (5pmol/ &micro;l&nbsp;)</p>
+                 <p>Forward primer (1:10)</p>
              </td>
              <td valign="top" width="84">
-                 <p>1 &micro;l</p>
+                 <p>3 &micro;l</p>
              </td>
          </tr>
          <tr>
              <td valign="top" width="205">
-                 <p>Reverse primer (5pmol/ &micro;l&nbsp;)</p>
+                 <p>Reverse primer (1:10)</p>
              </td>
              <td valign="top" width="84">
-                 <p>1 &micro;l</p>
+                 <p>3 &micro;l</p>
              </td>
          </tr>
@@ Line 2,014: / Line 2,892: @@
              </td>
              <td valign="top" width="84">
-                 <p>XX &micro;l</p>
+                 <p>ad. 15 &micro;l</p>
              </td>
          </tr>
@@ Line 2,022: / Line 2,900: @@
              </td>
              <td valign="top" width="84">
-                 <p><em>15 </em>&micro;l</p>
+                 <p><strong>15 </strong><strong>&micro;l</strong></p>
              </td>
          </tr>
@@ Line 2,045: / Line 2,923: @@
 <ul>
-     <li>Forward and Reverse primers should be added in 2 individual eppendorf tubes.</li>
+     <li>Forward and reverse primers should be added in 2 individual sample tubes!</li>
 </ul>
 </div>
@@ Line 2,054: / Line 2,932: @@
 <ul>
 <p><strong>RFP microscopy</strong></p>
-<p>To check if the transformed&nbsp;<em>E.coli</em>&nbsp;TOP10 show red fluorescence, the culture was examined by fluorescence microscopy. The RFP DsRed filter was used (excitation at 536 nm, emission at 582 nm). To prevent the cells from floating around they are fixed in 0,8 %.</p>
+<p>To check if the transformed&nbsp;<em>E.coli</em>&nbsp;TOP10 show red fluorescence, the culture was examined by fluorescence microscopy. The RFP DsRed filter was used (excitation at 536 nm, emission at 582 nm). To prevent the cells from floating around they are fixed in 0.8%.</p>
 <p>&nbsp;</p>
 <p><strong>Preparation of slides</strong></p>
 <ul>
-     <li>Prepare 0,8 % agarose with water and boil it up.</li>
+     <li>Prepare 0.8% agarose with water and boil it up.</li>
      <li>Pipet 500 &mu;L onto a slide and press another one on top. Let the agarose cure between both slides.</li>
      <li>Carefully remove the upper slide and put the sample name in one corner the one with the agarose.</li>
@@ Line 2,069: / Line 2,947: @@
 </div>
+</html>
+[[File:Counting_iGEM_Goettingen2015.jpeg|700px|thumb|center|]]
+<html>
+</div></div> <!--These are the closing tags for div id="mainContainer" and div id="contentContainer". The corresponding opening tags appear in the template that is {{included}} at the top of this page.-->
 </html>

Difference between revisions of "Team:Goettingen/Experiments"

Latest revision as of 00:00, 19 September 2015

Media/Buffer

LB Medium

"Fat" LB Medium

Media and Culture Methods for Dockerin Organisms of Origin

Phosphatase Activity plates, Sperber media

Esterase Activity plates, with 1% Tributyrin

Cellulase activity plates

1x TAE Buffer

Cloning Methods

PCR product purification using QIAquick® PCR Purification Kit (QIAGEN)

PCR Gel extraction, peqGOLD Gel Extraction Kit

Blunt End Ligation in pJET1.2 vector –Clone JET PCR Cloning Kit– (Thermo Scientific)

Sticky End T4 Ligation (Thermo Scientific)

TOPO® Cloning protocol usingChampion™ pET Directional TOPO® Expression Kits (Thermo Fisher Scientific)

Plasmid transformation into chemically competent E. coli

Electroporation of BL21 cells with pJET_RFP

Plasmid Extraction - using QIAprep Spin Miniprep Kit (QIAGEN)

Plasmid Extraction - using peqGOLD Plasmid Miniprep Kit I (PEQLAB Technologies)

Competent Cells

Preparation of competent E.coli cells

Transformation Efficiency Kit, RFP construct (iGEM)

Protein Extraction and Purification

Induction, harvest and disruption of expression cultures

Protein Purification (Protino® Ni-IDA 2000 His-Tag protein purification, Macherey-Nagel)

Affinity chromatography of His-tagged proteins

Size Exclusion Chromatography

Concentration of protein solutions

Bradford Assay

SDS Polyacrylamid Gel Electrophoresis

Western Blot

Activity Screens & Tests

Esterase activity test

Phosphatase activity test

Cellulase activity screening

Enzymatic Activity Test for Cellulase

Restriction Controls

Aan I (Psi I ) - thermo fisher scientific - restriction control protocol

Double digestion restriction control

Restriction control using fast and slow digestion enzymes

Scafoldin Restriction control

Esterase Restriction Control

Phosphatase Restriction Control

PCR Preparation Methods

Colony PCR

Phusion PCR

Sequencing

Protocol for Sanger sequencing

Overnight Sanger Sequencing

Fluorescence Microscopy

RFP microscopy