Difference between revisions of "Team:METU Turkey/Experiments"

Experiments

????????????????????????????????????????????

Protocols

Standard iGEM Protocols

Transformation Protocol:
1)Throw competent cell on ice
2) Mix ligation product 50 microliter cell+2 microliter plasmid
3)Incubate cells on ice 30 mins
4) Heat shock 55 sec CaCl2, 75 sec RuCl2
Add 900 ml LB
5)Incubate 37 celcius for 80 minute
6)Centrifuge at 3000 po m 10 mın
7)Discard supernatant
8)Resuspend pellet in 100 ml LB
9)Spread cells and wait 14-16 hours in the incubator
 
 
LB Broth Protocol:
1)10 gr peptone
2)5 gr yeast extract
3)10 gr NaCl
4)up to 1000ml dH20 & autoclave
 
 
LB Agar Protocol:
1)10 gr peptone
2)5 gr yeast extract
3)10 gr NaCl
4)15 gr agar
5)up to 1000ml dH20 & autoclave
6)use 20 gr for 1lt dH2O
 
 
ONC Protocol:
1)Put 5 ml LB into a tube.
2)Put a loop of E.coli dH5 aseptic.
3)Seal the tube using parafilm.
4)Place the tube diagonally into a shaker for 14-18 hours.(optimum 14)
 
 
Competent Cell Preparation by Calcium Chloride Protocol:
1)Inoculate 1ml ONC to 100 ml LB in a flask.
2)Incubate the flask for 2-4h at 37 ˚C, check via spectrophotometer at 
600nm for 0.300..
3)Divide the solution into two falcon tubes(50 ml).
4)Spin them down at +4 ˚C and 5000g for 5min.
5)Discard supernatant.
6)Resuspend the cells with 10 ml cold CaCl2.
7)Put in ice for 10 minutes.
8)Spin the suspension down at +4 ˚C, 5000g for 5 minutes.
9)Discard supernatant.
10)Add 10 ml cold CaCl2 and resuspend the cells.
11)Put the cells in ice for 30 min.
12)Centrifuge at 5000 rpm for 5 min at +4 ˚C.
13)Discard supernatant.
14)Put 1 ml CaCl2 and dissolve pellet.
15)Put it on ice for 5 min. and keep it at +4 ˚C.
 
 
Getting the DNA Parts from the Kit Plate:
1)Add 10 microliter of ddH2O into the wanted well.
2)Wait and get the part by pipetting.
3)Make sure to keep stock from these parts since there is so less of 
them.
4)In case of having too less sample, you can dilute the stock 10:1 
with ddH2O.
 
 
Midi Prep Plasmid Isolation Protocol:
A)Bacterial culture, harvest, and lysis.
1)Pellet 25 ml (high copy)  or 100ml (low copy) overnight LB culture 
at 6000xg for 15 min at +4˚C.
2)Homogeneously resuspend the bacterial pellet in 4 ml Buffer P1.
3)Add 4 ml Buffer P2, mix thoroughly by vigorously inverting 4-6 times, 
and incubate at room temperature for 5 min.
4)Add 4 ml Buffer P3, mix thoroughly by vigorously inverting 4-6 times, 
and incubate on ice for 15 min.
B)Bacterial lysate clearing
5)Centrifuge at ≥20.000 xg for 30 min at +4 ˚C. Re-centrifuge the 
supernatant at ≥20.000 xg for 15 min at +4 ˚C.
C)Bind, wash, and elute plasmid DNA on QIAGEN-tip.
6)Equilibrate a QIAGEN-tip 100 by applying 4ml Buffer QBT and allow 
column to empty by gravity flow.
7)Apply the supernatant(step 5) to the QIAGEN-tip and allow it to enter 
the resin by gravity flow.
8)Wash the QIAGEN-tip with 2x10 ml Buffer QC. Allow Buffer QC to move 
through the QIAGEN-tip by gravity flow.
9)Elute DNA with 5 ml Buffer QC into clean 2 ml, 15ml or 50ml vessel.
D)Precipitate, wash, and redissolve plasmid DNA
10)Precipitate DNA by adding 3.5 ml room-temperature isopropanol to the 
eluted DNA and mix. Centrifuge at ≥ 15.000 xg for 30 min at +4℃. Carefully 
decant supernatant.
11) Wash DNA pelelt with 2ml room-temperature 70% ethanol and centrifuge 
at  ≥ 15.000 xg for 10 min. Carefully decant supernatant.
12) Air-dry pellet for 5-10 min and redissolve DNA in a suitable volume of buffer.
 
 
Plasmid Isolation Protocol:
Resuspend the pelleted cells in 250μL of the Resuspension Solution. Transfer 
the cell suspension to a microcentrifuge tube. The bacteria should be resuspended 
completely by vortexing or pipetting up and down until no cell clumps remain.
Add  250μL of the Lysis Solution and mix thoroughly by inverting the tube 4-6 
times until the solution becomes viscous and slightly clear.
Add 250μL of the Lysis Solution and mix immediately and thoroughly by inverting 
the tube 4-6 times.
Centrifuge for 5 min to pellet cell debris and chromosomal DNA.
Transfer the supernatant to the supplied GeneJET spin column by decanting or 
pipetting. Avoid disturbing or transferring the white precipitate.
Centrifuge for 1 min. Discard the flow-through and place column back into the 
same collection tube.
Add 500μL of the Wash Solution to the GeneJET spin column. Centrifuge for 30-60 
seconds and discard the flow-through. Place the column back into the same collection 
tube.
Repeat the wash procedure using 500μL of the Wash Solution.
Discard the flow-through and centrifuge for an additional 1 min to remove residual 
Wash Solution. This step is essential to avoid residual ethanol in plasmid preps.
Transfer the GneJET spin column into a fresh 1.5 ml microcentrifuge tube. Add 50μL 
of the Elution Buffer to the center of GeneJET spin column membrane to elute the plasmid 
DNA. Take care not to contact the membrane with the pipette tip. Incubate for 2 min at 
room temperature and centrifuge for 2 min.
Discard the column and store the purified plasmid DNA at -20 ˚C.
 
 
80% Glycerol Preparation:
Add 80ml 99.7% glycerol to 20ml demineralized water
Autoclave

Documentation of the development of our project

????????????????????????????????????????????

Methodology

????????????????????????????????????????????