Team:Freiburg/Results/Surface
Results: Binding on Surface
Optimizing cell-free expression as such is already a challenging task. It becomes increasingly complicated if the expressed proteins ought to be immobilized on a glass surface directly after expression: The cell-free mix is a complex system mainly consisting of proteins, amino acids and other molecules. All of them compete with the protein of interest for binding at the glass surface. To overcome this hurdle we decided to fuse a tag to the proteins of interest that specifically bind to a chemically treated surface. To get such a tag-system to work, the surface has to be optimized in order to minimize unspecific binding.
Effective - The Unspecific Surface
For measuring in iRIf, the target proteins have to be fixed to a glass slide. Therefore we used silanes to introduce reactive groups on the surface. These silanes can bind to siliciumdioxide (glass) after reactive hydroxy groups were created by oxygen plasma activation. Adding either the silane GOPTS (3-Glycidyloxypropyltrimethoxysilane) or APTES (3-Aminopropyltriethoxysilane) allows us to bind certain chemical groups to the surface. The epoxy-group of GOPTS reacts covalently with amino-, hydroxy- and thiol-groups so that a large spectrum of molecules can be coupled. APTES on the other hand is not reactive itself but can be covalently fused to amino-groups with the homobifunctional cross-linker PDITC (p-Phenyldiisothiocyanate). For further information on chemistry and methods see surface chemistry methods . To evaluate these two chemistries, we compared the binding capacities of the respective surfaces on regular microscope glass slides. Self-purified GFP in different concentrations was spotted on both surfaces and the resulting fluorescence intensity was compared (figure 1). Especially for low concentrations it is obvious that APTES/PDITC has a higher binding capacity than the GOPTS surface under the conditions tested. Therefore, we continued our experiments using the PDITC-based surface chemistry.
With these results we decided to switch on special glass slides, suitable for iRIf. The slide chemistry is the very same as for normal glass slides. By performing iRIf experiments, we were able to detect the interaction of anti-GFP antibodies with hand-spotted GFP of different concentrations . To check for variations in different GFP-purification protocols, we compared GFPs obtained from different labs (GFP1 to GFP3). Figure 2 shows the pattern in which the different GFPs, the positive control biotinylated BSA (bBSA) and the negative control BSA were spotted. The total amount of spotted protein is annotated underneath.
The immobilized GFP was first blocked in the iRIf device with 10 mg/mL BSA. Anti-GFP in 1xPBS-buffer was flushed over the slide leading to a change in the optical thickness when binding to the GFP spots. Figure 3 shows a quotient picture for the binding of GFP-antibodies. For all GFP spots a binding could be observed. As the anti-GFP antibody was biotinylated the signal can be further amplified by a second binding step. Therefore streptavidin was flushed through the microfluidic chamber (figure 4). This step also confirms the binding of anti-GFP to the spots and therefore the specificity of the interaction. Furthermore, streptavidin binds to the positive control bBSA.
Selective - The Specific Surface
All the results presented above show, that the detection of antigen-antibody interactions is possible using the PDITC surface chemistry. But as we need a specific surface to bind antigens out of our cell-free expression mix, we wanted to build up a Ni-NTA (Nickel-Nitrolotriacetic acid) surface. We established a protocol for the Ni-NTA surface and optimized it. To enable proteins to bind to this surface they were genetically fused to a 10x histidine tag. Our Ni-NTA surface was optimized until the unspecific binding of other proteins from the cell-free mix was reduced to a minimal. To determine the specificity of our Ni-NTA surface we compared it to the PDITC surface. To asses the purification properties we used complete E. coli lysate transformed with either a tagged or an untagged GFP-construct. Additionally, purified His-GFP that was used in previous experiments was spotted and fluorescence intensity was measured. Figure 5 shows the intensities obtained for all spots: the intensity for the His-GFP lysate on the Ni-NTA surface is about four times higher than on the PDITC surface, while the values for the purified His-GFP are in a comparable range. The mean intensity for the untagged GFP-lysate spot is in the range of the background for the Ni-NTA surface and just slightly higher for the PDITC surface. These results clearly show that GFP cannot bind to Ni-NTA without a His-tag. The low fluorescence intensities for GFP lysate on PDITC is due to the fact, that non-fluorescent proteins in the lysate are bound as efficiently as GFP. This way the surface is blocked thereby preventing the binding of further GFP molecules resulting in an overall fluorescence decrease.
After we demonstrated that we can successfully bind His-tagged proteins to our Ni-NTA surface, we attempted to immobilize our cell-free expressed His-GFP-Lysate on this surface. You can find the results for this crucial part of our project on the main Results Page.
Covalent - Other Surface Systems
On the way to find the surface best suited for our needs we also worked with the Promega HaloTag system. The HaloTag, which can be fused to target proteins, binds covalently to chloroalkanes which are immobilized on the surface. We tested several ligands, which differed in length of the alkane chain and surface attachment method. The ligand working best for us was a 3-chloropropylsilane, which we directly immobilized on plasma activated iRIf slides. To test the surface we spotted our self-expressed Halo-GFP and Halo-mCherry as well as purified Halo-GFP as a positive control. Purified and untagged GFP served as a negative control. Both controls were kindly provided from the group of J. Piehler from Osnabrück. As an additional negative control we spotted bBSA. The iRIf measurement showed that the Halo-tagged GFPs were successfully immobilized on the surface. Unfortunately there was a lot of unspecific binding. The negative control spots nearly show as much binding to the surface as the positive control spots. Due to time limitations, optimizations that would be necessary to establish a specific surface based on the HaloTag system could not be performed. We decided to continue our work with the Ni-NTA surface which was established for future experiments.
Validation of Our Controls
Given that we were using purified His-tagged GFP for evaluation of our self-made surfaces and in further experiments as a positive control, we validated it by Western Blot. Therefore, we showed the presence of His-GFP with anti-His HRP conjugate (figure 8A). Additionally, we used the specific anti-GFP antibody (figure 8B) as for the detection in iRIf.
