1. Calculate total amount of volume of LB agar you would need to use
   • You need about 25mL for every 10cm plate and 10mL for every 6cm plate. (e.g. To make 20 x 10cm plates, you need 500mL of LB.)
2. For every 100mL of LB agar needed, measure out 4g of LB Agar Powder.
   • e.g. if you were to make 500mL of LB, you need 20g of LB Agar Powder
3. Put the agar powder in a flask
   • Note: Use a much bigger flask to prevent overflow when autoclaiving.
   • e.g. If you are making 500mL of LB, use a 750mL or 1L flask.
4. Put deionized water into the flask up to the desired volume.
   • Note: Do not mix. LB Agar is not supposed to dissolve in room temperature. If you mix the powder it will get stuck on the walls of the flask
5. Autoclave.
6. After autoclave, move to the hood. Let the LB agar cool until it’s less than 60ºC or until you can touch the flask. While waiting, you can start labeling the plates.
7. Insert any antibiotics/sugars needed. If you are not sure about the ratio, you can follow this simple example:

   50mL LB + 500µL Arabinose* + 50µL Ampicillin**
   *2mg/mL of Arabinose Stock Solution
   **100mg/mL of Ampicillin Stock Solution

8. Swirl the antibiotics/sugars that you just added for a minute.
9. Plate the LB agar into the petri dishes until it is about ⅓ of the level. Do not forget to keep the lid on before and after you plate.
10. Let it cool for about 5 minutes.
11. Invert each plate so that it is upside down
12. Store in the 4ºC freezer

Total Amount of Reagent:	100 mL	250 mL
Deionized Water	100 mL	250 mL
Yeast	1 g	2.5 g
Tryptone	0.5 g	1.25 g
NaCl	1 g	2.5 g

Materials

• 0.5% (w/v) yeast extract
• 2% (w/v) tryptone
• 10 mM NaCl
• 2.5 mM KCl
• 20 mM MgSO4

Per liter:

• 5 g yeast extract
• 20 g tryptone
• 0.584 g NaCl
• 0.186 g KCl
• 2.4 g MgSO4

Note: Some formulations of SOB use 10 mM MgCl2 and 10 mM MgSO4 instead of 20 mM MgSO4. SOB medium is also available dry premixed from Difco, 0443-17.
Adjust to pH 7.5 prior to use. This requires approximately 25 ml of 1M NaOH per liter.

15/10 medium

Growth of competent TOP10 cells in Example 2 of the Bloom05 patent is performed in 15/10 broth, which is similar to SOB:

• 1.5% yeast extract
• 1% Bacto-Tryptone
• 10mM NaCl
• 2mM KCl
• 10 mM MgCl2
• 10 mM MgSO4

Reagent	50 mL (in Mols)	100 mL (in M)	100 mL (in Grams)
Tryptone	(2% w/v) 1 g	2 g	2 g
Yeast Extract	(0.5% w/v) 0.25 g	0.5 g	0.5 g
NaCl	0.0005 M	0.01 mol	0.0584g
KCl	0.000125 M	0.0025 M	0.0186 g
MgCl2	0.0005 M	0.01 M	0.09521 g
Glucose	0.001 M	0.02 M	0.36032 g

General Overview:

1. D-Luciferin is too large of a chemical to cross the plasma membrane of e. Coli so cell lysis is required to extract luciferase.
2. After cell lysis, the reagent solution can be added to the lysis buffer. Light should be emitted within 5 to 10 seconds of adding the reagent solution.
3. The luciferase/luciferin reaction at 22.5 ºC theoretically offers the greatest light intensity.
4. Solutions of D-Luciferin should be aliquotted and stored in darkness at -80 ºC

Materials:

• D-Luciferin free acid
• ATP
• MgSO4 · 7H2O
• 1M HEPES Buffer
• Lysozyme
• 10 mM Tris-HCl

Lysis Buffer:

For E. coli cell lysis, use a freshly prepared lysozyme solution (10 mg/ml) in 10 mM Tris-HCl, pH 8.0.

Reagent Solution:

Prepare using ATP free water. Combine 1 mM luciferin or luciferin salt, 3 mM ATP and 15 mM MgSO4 in 30mM HEPES buffer, pH 7.8. Store substrate solution at -20ºC in polypropylene or glass.

Preparing 1mM D-Luciferin:

Directions for a 5 mg sample: Dissolve 0.034 gr dithiothreitol in 22 mL of QH2O. Add 0.2 mL of this DTT solution to the 5 mg d-luciferin. Add 4 uL of 10M NaOH to dissolve the luciferin. Dilute this into the remaining 21.8 mL of DTT solution and store as aliquots at - 80 ºC in darkness until use.

Procedure:
Bacterial lysis:

1. After 12-18 hours of inoculation of bacteria expressing luciferase plasmid, pipette 2 mL of cell culture into a clean 2 mL tube. Centrifuge at 10,000 rpm for 1 minute. Pour out liquid into a collection beaker. Continue this process until all of the cell culture (in the inoculation tube) is gone.
2. Resuspend the pellets in 350 ml of STET buffer (10 mM Tris-HCl with 1 mM EDTA)
3. Add 25 uL - 30 uL of lysozyme buffer to the resuspended pellet.
4. Mix by vortexing for 3 seconds.
5. Incubate for 2 hours at room temperature.
6. If the reagent is not added immediately, store the lysed bacteria in the -20 ºC freezer until use.

Addition of Reagent Solution:

1. Following the above instructions, prepare a 1mM sample of D-Luciferin.
2. Following the above recipe, prepare the reagent solution.
3. In a dark room, add about 250-350 uL of reagent solution to each sample of lysis product.
4. Light should be emitted within two-three seconds.

Example Calculations:
Lysis Buffer (Desired Total Volume: 15mL)

Chemical Name:	Tris-HCl	EDTA	NaCl
Molecular Weight:	N/A	292.23 g/mol	58.44 g/mol
Molarity Desired:	10 mM	1mM	0.1M
Calculation:	Dilute 1M Tris-HCl:
Final Amount:	150 uL (+14.85 mL ddH2O)	0.00438 g	0.08766 g

Lysozyme Solution (Desired Total Volume: 15mL)

Lysozyme Solubility:	10 mg lysozyme in 1 mL of 10 mM Tris-HCl
Desired Amount of Lysozyme Solution to Make:	15 mL
Amount of Lysozyme Needed:	10 mg x 15 = 150 mg
Amount of 10 mM Tris-HCl Needed:	15 mL

Reagent Solution (Desired total volume: 22 mL)

Chemical Name:	ATP disodium salt trihydrate	MgSO4•7H2O	HEPES Buffer	D-Luciferin free acid
Molecular Weight:	605.24 g/mol	246.5 g/mol	238.3 g/mol	280.33 g/mol
Molarity Desired:	3 mM	15 mM	30 mM	1 mM
Calculation:				Use the 1 mM stock solution created earlier
Final Amount:	0.039945 g	0.081345 g	0.1573 g	22 mL

This is the conditions we used to express chromoproteins.

Estimated time: 3 hours (plus 14-18 hour incubation)

Materials

2µl resuspended DNA

Competent cells (50ul per transformation)

Ice

2ml tube

42ºC water bath

SOC or LB media

1 LB plate and 1 LB+antibiotic per transformation

Spreader

37ºC incubator

Shaker

Procedure

1. Thaw competent cells on ice.
2. Add 50µL of thawed competent cells into pre-chilled 2ml tube.
3. Add 2µL of resuspended DNA to the 2ml tube. Pipet up and down a few times, gently. Keep the competent cells on ice.
4. Close tubes and incubate the cells on ice for 30 minutes.
5. Heat shock the cells by immersion in a pre-heated water bath at 42ºC for 60 seconds.
6. Incubate the cells on ice for 5 minutes.
7. Add 200 μl of SOC or LB media to each transformation
8. Incubate the cells at 37ºC for 2 hours at 260rpm in the shaker.
9. Label petri dishes with the appropriate antibiotic with the part number, plasmid backbone, antibiotic resistance, and date. Plate 200 µl of the transformation onto the labeled antibiotic dishes, and spread. This helps ensure that you will be able to pick out a single colony.
10. Spread remaining transformation onto labeled LB agar plate and spread, approx 50µl.
11. Incubate the plates at 37ºC for 12-18 hours, making sure the agar side of the plate is up. If incubated for too long the antibiotics start to break down and un-transformed cells will begin to grow. This is especially true for ampicillin - because the resistance enzyme is excreted by the bacteria, and inactivates the antibiotic outside of the bacteria.
12. You can pick a single colony, make a glycerol stock, grow up a cell culture and miniprep.

Controls

Competent cells on LB plate

Competent cells on LB + antibiotic plate

Competent cells + plasmid on LB plate

Estimated time

Materials

Biomiga Miniprep Kit

Procedure

1. Harvest the bacterial culture by centrifugation for 1 min at 10,000 rpm. Pour off the supernatant and blot the inverted tube on a paper towel to remove residue medium. Remove the residue medium completely.
2. Add 250 µL Buffer A1 (Add RNase A to Buffer A1 before use) and completely resuspend bacterial pellet by vortexing or pipetting
3. Add 250 µL Buffer B1, mix gently by inverting the tube 10 times (do not vortex), and incubate at room temperature for 5 minutes.
4. Add 350 µL Buffer N1, mix completely by inverting/shaking the vial for 5 times and sharp hand shaking for 2 times.
   Note: Incubating the lysate in ice for 1 min will improve the yield.
5. Centrifuge the lysate at 13,000 rpm for 10 minutes at room temperature. If the lysate doesn’t appear clean, reverse the tube angle, centrifuge for 5 more minutes and then transfer the clear lysate to DNA column.
6. Carefully transfer the clear lysate into a DNA column with a collection tube, avoid the precipitations, spin at 13,000 rpm for 1 minute, discard the flow-through and put the column back to the collection tube.
7. Add 500 µL Buffer KB into the spin column, centrifuge at 13,000 rpm for 1 minute. Remove the spin column from the tube and discard the flow-through. Put the column back to the collection tube.
8. Add 650 µL DNA Wash Buffer (Add ethanol to DNA wash buffer before use) into the spin column, centrifuge at 13,000 rpm for 1 minute at room temperature. Remove the spin column from the tube and discard the flowthrough.
9. Reinsert the spin column, with the lid open, into the collection tube and centrifuge for 2 minutes at 13,000 rpm.
10. Carefully transfer the spin column into a sterile 1.5 mL tube and add 50-100 µL (> 50 µL) Sterile ddH20 or Elution Buffer into the center of the column and let it stand for 2 minutes. Elute the DNA by centrifugation at 13,000 rpm for 1 minute. Reload the eluate into the column and elute again.

This is how you do restriction digest.

Link to NEB Protocol

To determine buffer for double digests, we used: NEB Protocl

Guide to heat inactivation: NEB Protocol

This is how you do gel electrophoresis.

Estimated time:

Materials
MinElute Midi Gel Extraction Kit

Procedure

1. Pre-weigh a 2.0mL microcentrifuge tube
2. Excise DNA fragment from agarose gel with clean, sharp scalpel. Place in the pre-weighed microcentrifuge tube. Minimize the exposure of the DNA samples under UV and amount of gel cut with DNA.
3. Weigh the tube and calculate the weight of the gel. For every 1 volume of gel (100mg = 100µl) add 3 times the volume of Buffer QG. The maximum amount of gel slice per spin column is 400mg.For >2% agarose gels, add 6 volumes of Buffer QG.
4. Incubate at 50ºC for 10 minutes (or until the gel has completely dissolved). Vortex the tube every 2-3 minutes during incubation to help dissolve the gel. If color is orange or violet after gel slice has dissolved, add 10µl 3M sodium acetate, pH 5.0. The color of the mixture will turn to yellow.
5. Add 1 gel volume of isopropanol to the sample and mix by inverting.
6. Place a MinElute spin column in a provided 2mL collection tube. Apply the sample in the 2.0mL microcentrifuge tube to the MinElute column and centrifuge for 1 min at 13,000 rpm. Discard the flow-through and place the MinElute column back into the same collection tube. If the sample volume exceeds 800µl, simply reload and spin again.
7. Add 500µl Buffer QG to the MinElute column and centrifuge for 1 minute at 13,000 rpm. Discard flow-through and place the MinElute column back into the same collection tube.
8. Add 750µl Buffer PE to MinElute column and centrifuge for 1 minute at 13,000 rpm. Discard flow-through and place the MinElute column back into the same collection tube. If the DNA will be used for salt-sensitive applications, such as direct sequencing and blunt-ended ligation, let the column stand 2-5 minute after addition of Buffer PE.
9. Centrifuge the column in the 2mL collection tube for 1 minute at 13,000 rpm again to remove residual ethanol.
10. Place each MinElute column into a clean 1.5mL microcentrifuge tube. To elute DNA, add 10µl Buffer EB or water to the center of the MinElute membrane. Let the column stand for 1 minute, and centrifuge the column for 1 minute at 13,000rpm.
11. Repeat step 12 but this time load the flow-through back to the membrane. Let the column stand for 1 minute, and centrifuge the column for 1 minute at 13,000rpm.
12. Check Gel extraction product with Nanodrop

This is the conditions we used for PCR.

This is the conditions we used for PCR cleanup.