Part | Description | Manufacturer / Partname |
---|---|---|
A fairly strong LED | In our case a 3W green 520nm LED | Cree XP-E on star circuit board |
A cooling element | Used to prevent the LED from overheating | Fischer Elektronik ICK S |
A constant-current-source | To ensure static LED light (no flickering) | Roschwege GmbH KSQ-3W |
An AC/DC rectifier | Used to grant direct current to the LED | Goobay 67951 |
Two optical lenses | Here we used two identical 60mm lenses | Thorlabs AC254-060-A |
A camera | We used a SLR camera | Canon 550D |
A microfluidics chamber | Our chamber consists of an iRIf slide attached to a PDMS flow chamber | Made ourselves |
Magnets | Used to attach the flow-cell to the device | 5mm Neodymium magnets |
A small syringe | We used a regular 10 ml syringe | BRAUN INJEKT 10ml |
A microfluidic tube | Used to connect the flow chamber with the syringe | - |
A case for the device | 5 mm thick acrylic glass cutouts to hold the parts in place | Ordered at http://formulor.com |
Difference between revisions of "Team:Freiburg/Results/Own Device"
Line 118: | Line 118: | ||
</div> | </div> | ||
<p> | <p> | ||
− | <a class="media lightbox_trigger" href="https://static.igem.org/mediawiki/2015/ | + | <a class="media lightbox_trigger" href="https://static.igem.org/mediawiki/2015/2/2f/Freiburg_iRIf_Device_Manual.pdf"><img alt="Manual for building your own DiaCHIP" class="media lightbox_trigger" src="https://static.igem.org/mediawiki/2015/c/c9/Freiburg_diachip_device_manual_preview.png" width="300"/></a> |
</p> | </p> | ||
<div class="tags"><span> | <div class="tags"><span> |
Revision as of 19:13, 12 September 2015
![](https://static.igem.org/mediawiki/2015/8/85/Freiburg_wiki_background_2_parted_left.png)
![](https://static.igem.org/mediawiki/2015/f/f4/Freiburg_wiki_background_2_parted_right.png)
Results: Device
Here you'll see what we were able to measure with our own device, as well as how to build your own, low-priced iRIf device.
Our own device is able to detect antigen/antibody binding
For testing our device we bound proteins derived from rabbits onto an iRIf slide in distinct spots (Fig 1 D). The proteins used were polyclonal anti-HCV (hepatitis C virus) antibodies, which we then aimed to detect with anti-rabbit antibodies. The reason for using the rabbit/anti-rabbit couple in this series of experiments was merely that we had had ample quantities of both left in our stocks. The binding layer on the iRIf slide consisted of an APTES/PDITC surface. The spots on the slide were made by pipetting 3 µl (500 µg/ml) rabbit-anti-HCV protein and 3 µl (1 mg/ml) BSA in an alternating pattern onto the slide. After incubation, the slide was blocked for 30 min in BSA solution. A Canon 50D camera was used to record the measurement and was set to take one picture every 5 seconds. The exposure time was set so that the pixels in the image were approx. 80% of maximum light saturation before the solution was flown onto the chip. The antibody solution was pipetted into the flow-chamber without the use of any microfluidics device. Instead a syringe was loaded with 500 µl [5 µg/ml] anti-rabbit antibody solution (diluted in PBS) and slowly released into the binding chamber of the device by gently dispensing the solution from the syringe. As can be seen in the figure C, the quotient picture clearly showed binding of anti-rabbit to the rabbit protein spots. The BSA control-spots showed none or negligible unspecific binding.
How to build your own device
General principle
As can be seen in the illustration below, the basic setup is fairly simple. Light from an LED enters a lense where the light rays are made parallel. To achieve this, the distance from LED to the lense has to be exactly one focal length. The light then hits the iRIf slide, where it gets reflected (reflecting at the same angle it hit the slide) and enters a second lense, whose purpose is to project a sharp image of the slide onto the CCD chip of the camera.
Construction guidance
![](https://static.igem.org/mediawiki/2015/8/88/Freiburg_results-device_3d_no_walls.png)