Difference between revisions of "Team:UCLA/Notebook/Honeybee Silk/21 July 2015"

Line 287: Line 287:
 
<div id="contentContainer"> <!--The closing tag for contentContainer should be placed at the bottom of each content page.-->
 
<div id="contentContainer"> <!--The closing tag for contentContainer should be placed at the bottom of each content page.-->
 
</html>
 
</html>
 +
='''Inclusion Body Purification of Honeybee Protein'''=
 
#Determine wet wet weight of cell pellet after spinning liquid culter at 10000 x g for 10 min.
 
#Determine wet wet weight of cell pellet after spinning liquid culter at 10000 x g for 10 min.
 
## 1.25 g
 
## 1.25 g

Revision as of 20:36, 24 August 2015

Inclusion Body Purification of Honeybee Protein

  1. Determine wet wet weight of cell pellet after spinning liquid culter at 10000 x g for 10 min.
    1. 1.25 g
  2. Resuspend in 5 ml/g Bug Buster (1x) by pipetting and gently vortexing.
    1. This is 6.25 ml in our case
  3. Put on shaker or rotating mixer for 15 min at RT
    1. Took our first fraction at this point of the full cell lysate (F1)
  4. Centrifuge 16000 g 20 min at 4 degrees C
    1. Took next fraction at this point of the supernatant, labeled (S1)
  5. Resuspend pellet in same volume of 1X bugbuster as before
    1. 6.25 ml
  6. Pipette up and down and vortex gently to get an even suspension.
    1. Took third fraction at this point (F2)
    2. I did not go to great lengths to get an even suspension here, but I noticed in retrospect that the protocol emphasized the importance of this in order to get pure inclusion bodies.
  7. Add dry lysozyme to final concentration of 200 ug / ml
    1. For 6.25 ml solution I added around 1.25 mg of lysozyme
    2. Added 1 ul of DNAse to remove chromosomal DNA.
  8. Add 6 volumes of 1:10 diluted bugbuster (.1X)
    1. At this point we split the solution up into two 50 ml falcon tubes and added 18.75 ml of .1X bugbuster to each tube
  9. Centrifuge 16000g 15 min. 4 degrees C to collect inclusion bodies.
  10. Remove supernatant w/ pipette, take next fraction (S3)
    1. After spinning this down, there was a pellet, with chromosomal DNA.
    2. It was difficult to remove the supernatant because the viscous liquid kept getting sucked up and bringing the pellet up with it.
  11. Resuspend pellet in 1/2 volume of original 0.1X bug buster solution
    1. 9.375 ml per tube
  12. Mix to get an even suspension by pipetting and vortexing for several minutes and spin down as in step 9.
  13. Repeat was two more times.
    1. Take samples of supernatant at each wash step
  14. Resuspend inclusion body pellet in 3% SDS solution and incubate at 60 C in the water bath for 2 hours
    1. I used around 2 ml, but I probably could have used less, because the pellet dissolves well in the heat
  15. Store solution at 4C until further required.
    1. I noticed that after a day in the 4C, the solution gelled up.
    2. According to protocol, storage at temperatures below 4°C may cause precipitation of the detergents in BugBuster reagent. Incubate in a room temperature water bath with gentle swirling to redissolve.